Scag Power Equipment LIBERTY Z Operator's Manual
  1. Manuals
  2. Brands
  3. Scag Power Equipment Manuals
  4. Lawn Mower
  5. LIBERTY Z
  6. Operator's manual

Scag Power Equipment LIBERTY Z Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Congratulations on owning a Scag mower! This manual contains the operating
instructions and safety information for your Scag mower. Reading this manual
can provide you with assistance in maintenance and adjustment procedures to
keep your mower performing to maximum efficiency. The specific models that
this book covers are listed on the inside cover. Before operating your machine,
please read all the information enclosed.
© 2020
Scag Power Equipment
Division of Metalcraft of Mayville, Inc.
OPERATOR'S
MANUAL
Models:
SZL36H-18FR
SZL48H-21FR
SZL52H-23FR
SZL61H-24FR
PART NO. 03468
PRINTED 09/20
PRINTED IN USA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LIBERTY Z and is the answer not in the manual?

Questions and answers

Stephen Brandenburg
March 8, 2025

where can I find the PTO switch on the Skag Liberty Z mower

1
1 comments:
Mr. Anderson
March 8, 2025

The PTO switch on the Scag Liberty Z mower is located on the instrument panel.

This answer is automatically generated

0
Bill Naccarato
July 4, 2025

What is the towing capacity of the scab liberty

0
Mike A
April 28, 2025

Does anyone offer a workshop manual for real mechanics?

0
Reginald M Proctor
April 21, 2025

How much oil for a change on the Liberty Z 61 in

0

Subscribe to Our Youtube Channel

Related Manuals for Scag Power Equipment LIBERTY Z

Summary of Contents for Scag Power Equipment LIBERTY Z

  • Page 1 The specific models that this book covers are listed on the inside cover. Before operating your machine, please read all the information enclosed. © 2020 PART NO. 03468 Scag Power Equipment PRINTED 09/20 Division of Metalcraft of Mayville, Inc. PRINTED IN USA...
  • Page 2 WARNING FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY OR DEATH. • Read this manual completely as well as other manuals that came with your mower. • DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the cutter deck down).

  • Page 3: Table Of Contents

    Table of Contents Table of Contents SECTION 1 - GENERAL INFORMATION ...................1 1.1 INTRODUCTION ............................1 1.2 DIRECTION REFERENCE ...........................1 1.3 SERVICING THE ENGINE AND DRIVE TRAIN COMPONENTS ..............1 1.4 SYMBOLS ..............................2 SECTION 2 - SAFETY INFORMATION ..................3 2.1 IMPORTANT SAFETY PRACTICES FOR RIDE-ON MOWERS ..............3 2.2 INTRODUCTION ............................3 2.3 SIGNAL WORDS ............................3 2.4 CHILDREN ..............................3...
  • Page 4 Table of Contents 4.14 ADJUSTING CUTTING HEIGHT ......................18 4.15 TOWING (OPTIONAL HITCH ACCESSORY)(NOT AVAILABLE FOR SZL36) ........19 SECTION 5 - TROUBLESHOOTING CUTTING CONDITIONS ..........20 SECTION 6 - ADJUSTMENTS ....................23 6.1 PARKING BRAKE ADJUSTMENT ......................23 6.2 TRACKING ADJUSTMENT ........................24 6.3 THROTTLE CONTROL AND CHOKE ADJUSTMENTS ................24 6.4 BELT ADJUSTMENT ..........................24 6.5 BELT ALIGNMENT .............................25 6.6 CUTTER DECK ADJUSTMENTS ......................25...

  • Page 5: Section 1 - General Information

    Attachments and accessories manufactured by companies industry. However, the prolonged life and maximum other than Scag Power Equipment are not approved for use efficiency of your mower depends on you following the on this machine. See Section 8, Paragraph 8-1.

  • Page 6: Symbols

    Section 1 1.4 SYMBOLS SYMBOL DESCRIPTION SYMBOL DESCRIPTION Choke Transmission Parking Brake Spinning Blade 48071S On/Start Spring Tension on Idler Off/Stop Falling Hazard Thrown Object Hazard Fast Slow Continuously Variable - Linear Cutting Element - Basic Symbol Pinch Point Cutting Element - Engage 481039S Hour meter/Elapsed Operating Hours Cutting Element - Disengage...

  • Page 7: Section 2 - Safety Information

    Section 2 SAFETY INFORMATION 2.1 IMPORTANT SAFETY PRACTICES FOR SIGNAL WORD: RIDE-ON MOWERS It is a distinctive word found on the safety decals on the machine and throughout this manual that alerts the viewer to the existence and relative degree of the hazard. This cutting machine is capable of amputating hands and feet and throwing objects.

  • Page 8: Before Operation Considerations

    Section 2 3. Be alert and turn machine off if a child or other 6. DO NOT carry passengers. person enters the area. 7. DO NOT operate the machine under the influence of 4. DO NOT allow children to ride or play on the alcohol or drugs.

  • Page 9: Testing The Safety Interlock System

    If the safety interlock system and the vapors are explosive. does not operate as described below, contact your local Authorized Scag Power Equipment Dealer immediately to 1. See Section 7.5 ENGINE FUEL SYSTEM for fueling have the safety interlock system repaired.

  • Page 10: Operation Considerations

    Section 2 6. Keep flammable objects (cigarettes, matches, etc.), 11. Never direct the discharge of material toward anyone. Avoid discharging material against a wall open flames and sparks away from the fuel tank and fuel container. or obstruction. Material may ricochet back toward operator.

  • Page 11: Transporting The Mower

    Section 2 23. Disengage power to the attachments when transporting or when not in use. 24. The machine and attachments should be stopped and inspected for damage after striking a foreign object, and damage should be repaired before restarting and operating the machine. CAUTION Figure 2-1.

  • Page 12: Using A Spark Arrestor

    Section 2 6. To reduce fire hazard, keep the cutting units, drives, 17. Charge batteries in an open, well ventilated area, muffler and engine free of grass, leaves, excessive away from spark and flames. Unplug charger before grease, oil and dirt. Clean up oil or fuel spillage and connecting or disconnecting from battery.

  • Page 13: Safety Decal Location

    Section 2 2.13 SAFETY DECAL LOCATION WARNING WARNING DANGER DANGER (Under Seat) 486151 DANGER DANGER (molded into tank) 483505 485667 (molded into tank) WARNING WARNING 483402 DANGER DANGER 483505 WARNING WARNING DANGER DANGER CUTTER WARNING WARNING DECK DOWN 483402 483505 485843 485843...

  • Page 14: Section 3 - Specifications

    Section 3 SPECIFICATIONS 3.1 ENGINE General Type ....................Heavy Duty Industrial/Commercial Gasoline Model: Scag Model SZL36H-18FR ......................Kawasaki FR600V Scag Model SZL48H-21FR ......................Kawasaki FR651V Scag Model SZL52H-23FR ......................Kawasaki FR691V Scag Model SZL61H-24FR ......................Kawasaki FR730V Displacement: Kawasaki FR600V .............................. 603cc Kawasaki FR651V .............................. 726cc Kawasaki FR691V ..............................

  • Page 15: Cutter Deck

    Section 3 Tire Pressure: Front Caster............................... 25 PSI Drive ..................................8 PSI Fuel Tank ....3-1/2 Gallon (36) or 5-1/2 Gallon (48/52/61) Polyetholene Tank with Large Opening and Fuel Cap Seat ..........Padded, Thick Cushion with Extra Spring Support and Armrests(Excludes 36" Model) Travel Speed: Forward ..............................

  • Page 16: Section 4 - Operating Instructions

    Section 4 OPERATING INSTRUCTIONS 1. Ignition Switch (Figure 4-1). The ignition switch WARNING is used to start the engine and has three positions; OFF, ON, and START. 2. Mower Deck Switch (Figure 4-1). Used to engage Do not attempt to operate this mower unless you and disengage the mower drive system.

  • Page 17: Safety Interlock System

    If the safety interlcok system does not operate as engage and disengage the parking brakes. Pull the descibed below, contact your local Scag Power Equipment lever back to engage the parking brakes. Push the Dealer immediately for repair of the safety interlock system.

  • Page 18: Initial Run-In Procedures

    Section 4 4.5 STARTING THE ENGINE 4. Sit in the seat in the operating position, engage the parking brake, place the steering control levers in the neutral lock position, move the PTO switch to the OFF (down) position, and start the engine. With the CAUTION engine running, engage the PTO switch to the ON (up) position, and rise slightly off of the seat.
  • Page 19 Section 4 - NOTE - Practice operating the mower until you are comfortable with the controls before proceeding Smooth operation of the steering levers will to mow. produce smooth mower operation. While learning the operation of the steering controls, keep the travel speed low.

  • Page 20: Engaging The Deck Drive (Cutter Blades)

    Section 4 4.8 SLOPE OPERATION To steer right while traveling in reverse, allow the right steering control lever to move forward. The further the control is allowed to move forward, the quicker the mower Slopes are a major factor related to loss of control and tip will turn right.

  • Page 21: Parking The Mower

    Section 4 4.9 PARKING THE MOWER 12. Loss of traction may occur when traveling down hill. Weight transfers to the front of the machine and may cause the drive wheels to slip causing loss of 1. Park the machine on a flat, level surface only. Do not braking or steering.

  • Page 22: Removing Clogged Material

    Section 4 2. The discharge chute must not be removed and 4.11 REMOVING CLOGGED MATERIAL must be kept in the lowest position to deflect grass clippings and thrown objects downward. Direct the side discharge away from sidewalks or streets to DANGER minimize cleanup of clippings.

  • Page 23: Towing (Optional Hitch Accessory)(Not Available For Szl36)

    Section 4 Figure 4-5. Adjusting Cutting Height 3. Lift the pin and insert into the cutting height index at the desired cutting height. See Figure 4-5. Slowly release the foot pedal. A deck height decal is located next to the cutting height index as an aid in adjusting the deck to the desired height.

  • Page 24: Section 5 - Troubleshooting Cutting Conditions

    Section 5 TROUBLESHOOTING CUTTING CONDITIONS CONDITION CAUSE CURE STRINGERS - OCCASIONAL Low engine RPM Run engine at full RPM BLADES OF UNCUT GRASS Ground speed too fast Slow speed to adjust for conditions Wet grass Cut grass after it has dried out Dull blades, incorrect sharpening Sharpen blades Deck plugged, grass accumulation...
  • Page 25 Section 5 TROUBLESHOOTING CUTTING CONDITIONS (CONT'D) CONDITION CAUSE CURE U N E V E N C U T O N F L AT Lift worn from blade Replace blade GROUND - WAVY HIGH-LOW APPEARANCE, SCALLOPED Blade upside down Mount with cutting edge toward ground CUT, OR ROUGH CONTOUR Deck plugged, grass accumulation Clean underside of deck...
  • Page 26 Section 5 TROUBLESHOOTING CUTTING CONDITIONS (CONT'D) CONDITION CAUSE CURE SCALPING - BLADES HITTING Low tire pressures Check and adjust pressures DIRT OR CUTTING VERY CLOSE TO THE GROUND Ground speed too fast Slow speed to adjust for conditions May need to reduce ground speed, raise Cutting too low cutting height, change direction of cut, and/or change pitch and level...

  • Page 27: Section 6 - Adjustments

    Section 6 ADJUSTMENTS 6.1 PARKING BRAKE ADJUSTMENT WARNING Do not operate the mower if the parking brake is not operable. Possible severe injury could result. The parking brake linkage should be adjusted whenever the parking brake lever is placed in the “ENGAGE” position and RELEASE BRAKE the parking brake will not prevent the mower from moving.

  • Page 28: Tracking Adjustment

    These adjustments must be performed by your Authorized indication that the left wheel is turning faster than Scag Power Equipment Dealer to ensure proper and the right wheel. To adjust this condition, proceed as efficient running of the engine. Should either need follows: adjustment, contact your authorized Scag service center.

  • Page 29: Belt Alignment

    Section 6 WARNING ADJUSTMENT If the pump drive belt fails, steering control will be lost which could result in serious injury or death. Replace the pump drive belt as needed or every ADJUSTMENT 400 hours / 2 years, whichever occurs first. 6.5 BELT ALIGNMENT Belt alignment is important for proper performance of your Scag mower.
  • Page 30 Section 6 - NOTE - To prevent the cutter deck from teetering, all four (4) cutter deck hanging links must have tension on them. If all four links do not have tension on ADJUSTMENT them and the deck teeters, you must readjust the cutter deck as outlined in the procedures above.
  • Page 31 Section 6 ADJUSTMENT ADJUSTMENT Figure 6-8. Cutter Deck Height Adjustment - Right Side 3. Turn the elastic stop nuts an equal amount of turns either clockwise to raise or counter-clockwise to lower the cutter deck until the measurement at the cutter blade is 3"...

  • Page 32: Section 7 - Maintenance

    Section 7 MAINTENANCE 7.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS HOURS PROCEDURE COMMENTS BREAK-IN (FIRST 10) Check all hardware for tightness Check hydraulic oil level See paragraph 7.3 Check all belts for proper alignment See paragraph 7.8 Change engine oil See paragraph 7.4 Check hydraulic hoses for leaks U s e ex t r e m e c a u t i o n w h e n...

  • Page 33: Grease Fitting Location Chart

    Section 7 7.2 GREASE FITTING LOCATION CHART - GREASE GUN Not Applicable to 36” models Not Applicable to 36” models Not Applicable to 36” models Not Applicable to 36” models...

  • Page 34: Hydraulic System

    Section 7 7.3 HYDRAULIC SYSTEM 5. Once the hydraulic system has drained, install new hydraulic oil filters to both axles by hand, turn 3/4 to one complete turn after filter gasket contacts the A. CHANGING HYDRAULIC OIL filter base. 6. Reinstall the filter guards and torque the screws to The hydraulic system oil and filter should be changed after 65 in/lbs.

  • Page 35: Engine Oil

    Section 7 7.4 ENGINE OIL 9. Reinstall the fill port plug on the top of the transaxle. 10. The hydraulic system will need to be purged of all air. Raise the rear of the machine so the drive A. CHECKING ENGINE CRANKCASE OIL LEVEL wheels are off the ground.

  • Page 36: Engine Fuel System

    Section 7 To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Extinguish all cigarettes, cigars, pipes and other sources of ignition. FILLER NECK ENGINE OIL INSERT DRAIN Figure 7-5.

  • Page 37: Engine Air Cleaner

    Section 7 3. NEVER fuel the machine indoors or in an enclosed trailer. FUEL SHUTOFF 4. NEVER store the machine or fuel container where VALVE there is an open flame, spark or pilot light such as on ENGINE FUEL FILTER a water heater or other appliances.

  • Page 38: Battery

    Section 7 WARNING Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to cause cancer and reproductive harm. ENGINE AIR Wash hands after handling. FILTER LIFT TABS WARNING Electric storage battery fluid contains sulfuric acid which is POISON and can cause SEVERE CHEMICAL BURNS.

  • Page 39: Drive Belts

    Section 7 7.9 CUTTER BLADES Whenever possible, remove the battery from the mower before charging and make sure the electrolyte covers the plates in all cells. A. BLADE INSPECTION 1. Remove the ignition key before servicing the blades. WARNING 2. Raise the mower deck to the highest position. Place the lanyard pin in the highest cutting height position to prevent the cutter deck from falling.

  • Page 40: Tires

    Section 7 - NOTE - CAUTION DO NOT sharpen the blades beyond 1/3 of the width of the blade. See Figure 7-9. Inspect the cutter blade spacer(s) and washer 1. Sharpen the cutting edge at the same bevel as the for wear and/or cupping.

  • Page 41: Body, Deck, And Upholstery

    Section 7 7.11 BODY, DECK, AND UPHOLSTERY CAUTION Do not wash any portion of the equipment while it is hot. Do not wash the engine; use compressed air. 1. After each use, wash the mower and cutter deck. Use cold water and automotive cleaners. Do not use pressure cleaners.

  • Page 42: Section 8 - Illustrated Parts List

    Section 8 ILLUSTRATED PARTS LIST 8.1 SCAG APPROVED ATTACHMENTS AND ACCESSORIES. Attachments and accessories manufactured by companies other than Scag Power Equipment are not approved for use on this machine. Scag approved attachments and accessories: • GC-SZL/SFZ/SPZ (p/n 901K, requires p/n 9071 (36"), 9069 (48") or 9070 (52") baffle kit) •...

  • Page 43: Notes

    Section 8 NOTES...

  • Page 44: Cutter Deck

    Section 8 36H CUTTER DECK 11 12...
  • Page 45 Section 8 36H CUTTER DECK Ref. No. Part No. Description 485805 Belt, Cutter Deck 483422 Pulley, 5" Idler 04112-06 Nut, 3/4-16 Spiral Lock 04063-01 Key, 1/4 x 1/4 x 1-1/4" 483324 Pulley, 5.73" OD - 25mm Bore 04021-09 Nut, 3/8-16 Elastic Stop 04041-38 Flat washer, 3/8-.406 x 2.25 x .188 483453-03...

  • Page 46: 52H & 61H Cutter Decks

    Section 8 48H, 52H & 61H CUTTER DECKS 48 49...
  • Page 47 Section 8 48H, 52H & 61H CUTTER DECKS Part No. Qty Description 48 52 61 Part No. Description 48 52 61 483303 Bearing 485350 Belt, Cutter Deck - 48H 43693 Spacer 485424 Belt, Cutter Deck - 52H 462014 Spindle Housing (incl. 34, 35) 486027 Belt, Cutter Deck - 61H 43694...

  • Page 48: Cutter Deck Controls

    Section 8 36H CUTTER DECK CONTROLS...
  • Page 49 Section 8 36H CUTTER DECK CONTROLS Ref. No. Part No. Description 428142 Link, Deck Lift - LH 04117-02 Nut, 3/8-16 Elastic Stop 04001-32 Bolt, Hex Head 3/8-16 x 1-1/4" 43086 Bushing 04061-07 Cotter Pin, 3/16 x 1" 04040-07 Flatwasher, 1/2-.531 x 1.062 x .095 04021-07 Nut, 1/2-13 Elastic Stop 431072...

  • Page 50: 52H & 61H Cutter Deck Controls

    Section 8 48H, 52H & 61H CUTTER DECK CONTROLS...
  • Page 51 Section 8 48H, 52H & 61H CUTTER DECK CONTROLS Ref. No. Part No. Description 428142 Link, Deck Lift - LH 04117-02 Nut, 3/8-16 Elastic Stop 04001-32 Bolt, Hex Head 3/8-16 x 1-1/4" 43086 Bushing 04061-07 Cotter Pin, 3/16 x 1" 04040-07 Flatwasher, 1/2-.531 x 1.062 x .095 04021-07...

  • Page 52: Sheet Metal Components

    Section 8 36H SHEET METAL COMPONENTS TO BOTTOM OF SEAT MOUNTING PLATE...
  • Page 53 Section 8 36H SHEET METAL COMPONENTS Ref. No. Part No. Description 486499 Seat, SZL 483559 Cable, Seat Stop 04001-59 Bolt, Hex Head 1/4-20 x 1-1/4" 04019-02 Nut, 1/4-20 Serrated Flange 463331 Seat-Plate W/Decal 04117-02 Nut, Flanged Elastic Stop, 3/8-16 04001-09 Bolt, Hex Head 5/16-18 x 1"...

  • Page 54: 52H & 61H Sheet Metal Components

    Section 8 48H, 52H & 61H SHEET METAL COMPONENTS TO BOTTOM OF SEAT MOUNTING PLATE...
  • Page 55 Section 8 48H, 52H & 61H SHEET METAL COMPONENTS Part No. Description Part No. Description 485939 Caster Wheel Assembly (incl. 32, 33, 486602 Seat, SZL w/Armrests 486633 Armrest, RH (48H, 52H, 61H) 34, 35) 485243 Bearing 486634 Armrest, LH (48H, 52H, 61H) 483559 Cable, Seat Stop 431052...

  • Page 56: Drive System Components

    Section 8 36H DRIVE SYSTEM COMPONENTS...
  • Page 57 Section 8 36H DRIVE SYSTEM COMPONENTS Part No. Description Part No. Description 485808 Belt, Transmission SZL-36 *485192 Engine, Kawasaki - FR600V (INCL. 3,4,5) 04001-51 Bolt, Hex Head 3/8-16 x 3-3/4" Oil Drain, Kawasaki 04043-04 Flatwasher, 3/8-.391 x .938 x .105 484210 Gasket, Exhaust 486045...

  • Page 58: 52H & 61H Drive System Components

    Section 8 48H, 52H & 61H DRIVE SYSTEM COMPONENTS 74 14 66 18 70 58...
  • Page 59 Section 8 48H, 52H & 61H DRIVE SYSTEM COMPONENTS Part No. Description Part No. Description *485219 Engine, Kawasaki - FR651V 04069-01 Pin, Rue Cotter - 3/8" *485220 Engine, Kawasaki - FR691V 04041-07 Flatwasher, 3/8-.391 x .938 x .105 04030-04 Lockwasher, 3/8" *486 Engine, Kawasaki - FR730V 463187...

  • Page 60: Electrical System

    Section 8 36 ELECTRICAL SYSTEM STARTER GROUND...
  • Page 61 Flatwasher, 1/4-.312 x .750 x .065 462942 Instrument Panel w/Decal, SZL-36 484565 Hourmeter, Inductive 485833 Switch, PTO 04030-04 Washer, Lock 3/8 Spring 04001-19 Bolt, Hex Head 3/8-16 x 1" 04132-01 Threaded Insert, 3/8-16 * Not available through Scag Power Equipment. Purchase locally.

  • Page 62: 61 Electrical System

    Section 8 48, 52 & 61 ELECTRICAL SYSTEM STARTER GROUND 37 33...
  • Page 63 Key, 1/4 x 1/4 x 1-1/4" 48029-13 Cable, Battery - 25" Red (61) 483958 Diode (part of wire harness) 04021-10 Nut, 5/16-18 Elastic Stop 04030-04 Washer, Lock 3/8 Spring 04031-03 Washer, Lock 5/16 Ext Tooth (ground) * Not available through Scag Power Equipment. Purchase locally.

  • Page 64: Fuel System

    Section 8 FUEL SYSTEM *For California Only SZL-36 Models Only SZL-48 52 & 61 Models Only Purge Tank Purge Tank...
  • Page 65 Section 8 FUEL SYSTEM Ref. No. Part No. Description 484286 Fuel Cap *484297 Fuel Cap, C.A.R.B. 484279-03 Fuel Neck Insert 484333 Remote Vent, No Valve 484285 Grommet, Kelch 485393 Fuel Gauge (requires #6) 485394 Grommet, Fuel Gauge 485391 Valve, Fuel Shut Off 482571 Bushing, .56 Dia.

  • Page 66: Liberty Transaxle (Zt-2800 36")

    Section 8 LIBERTY TRANSAXLE (ZT-2800 36")
  • Page 67 Section 8 LIBERTY TRANSAXLE (ZT-2800 36") Ref. Ref. Part No. Description Part No. Description HG71854 Kit, Filter Guard (LH) HG53246 Screw, Hex Washer HG54730 Plug, External Hex Vent 9/16-18 HG73041 Kit, Filter Guard (RH) HG51048 Swashplate, Trunnion HG73096 Kit, Side Cover LH HG73095 Kit, Side Cover RH HG50551...

  • Page 68: Liberty Transaxle (Zt-2800 48/52")

    Section 8 LIBERTY TRANSAXLE (ZT-2800 48/52")
  • Page 69 Section 8 LIBERTY TRANSAXLE (ZT-2800 48/52") Ref. Ref. Part No. Description Part No. Description HG53246 Screw, Hex Washer HG72882 Kit, 16cc Cylinder Block Assembly HG50752 Screw, Hex Washer 1/4-20 x .75 HG54730 Plug, External Hex Vent 9/16-18 HG73096 Kit, Side Cover LH HG72291 Kit, Gerotor Seal HG71854...

  • Page 70: Liberty Transaxle (Zt-2800 61")

    Section 8 LIBERTY TRANSAXLE (ZT-2800 61")
  • Page 71 Section 8 LIBERTY TRANSAXLE (ZT-2800 61") Ref. Ref. Part No. Description Part No. Description HG71854 Kit, Filter Guard (LH) HG53246 Screw, Hex Washer HG73041 Kit, Filter Guard (RH) HG54730 Plug, External Hex Vent 9/16-18 HG51048 Swashplate, Trunnion HG73096 Kit, Side Cover LH HG50551 Bearing, Thrust 30 x 52 x 13 HG73095...

  • Page 72: Replacement Decals And Information Plates

    Section 8 REPLACEMENT DECALS AND INFORMATION PLATES WARNING WARNING DANGER DANGER WARNING WARNING CUTTER DECK DOWN 486493...
  • Page 73 485820 Decal, Instrument Panel - SZL (36) 485387 Decal, Instrument Panel - SZL (48 52 & 61) 486517 Decal. Liberty Z - Fuel Tank 485821 Decal, Belt Routing - SZL (36) 485516 Decal, Belt Routing - SZL(48 52& 61) 486493...

  • Page 74: Electrical Schematic

    Section 8 ELECTRICAL SCHEMATIC BRAKE INTERLOCK SWITCH WHITE BLACK LH NEUTRAL SWITCH GREEN BLACK W/RED STRIPE SEAT WHITE SWITCH GREEN GREEN BLACK BLACK W/RED STRIPE GREEN RH NEUTRAL SWITCH WHITE BLACK W/RED STRIPE GREEN Position Key Switch Legend G + M + A LIGHT KIT BLACK B + L + A...

  • Page 75: Limited Warranty - Szl

    If the mower is cutting more than the owners single property, it is deemed commercial use and the warranty does not apply. Scag Power Equipment reserves the right to deny and / or void the non- commercial warranty if it believes it to be in commercial use.
  • Page 76 © 2020 Scag Power Equipment Division of Metalcraft of Mayville, Inc.

This manual is also suitable for:

Szl36h-18frSzl48h-21frSzl52h-23frSzl61h-24fr

Table of Contents

Save PDF