Table of Contents
Advertisement
Chapter 1 MaxiProx System Overview
The MaxiProx Reader is a self-contained proximity Reader. The two piece polycarbonate enclosure has
an O-ring that weather seals the enclosure pieces together and a cable fitting that seals the cable entry.
The water-resistant unit is designed for outdoor use. The enclosure is mountable on a single gang
electrical box. A bi-color LED and audible tone provide user feedback. Configurable open collector data
outputs provide the data to the Host. Configurable DIPswitches and jumpers provide choice of data
interfaces between Wiegand, Clock and Data, RS 232 and RS422. The data interface is configured as
ordered from the factory, but can be changed in the field - please contact
assistance. A tamper switch can alert the Host when the enclosure is opened. Internal DIP switches
and jumpers provide for configuration of the outputs, audible tone and LED control options.
Installation of the MaxiProx Reader consists of mounting, connecting the cable to the Host and
+12VDC or +24VDC power, verifying the DIPswitch and jumper settings, verifying Autotune, and
verifying the reading of a transponder.
1.1 Operation
1.1
Transponders (Proximity Cards or ProxKeys) are presented to the front of the MaxiProx. The LED is
when ready to read a transponder. The LED turns
is read and the message is transmitted to the Host computer or interface panel. The system is ready for
another transponder as soon as the LED returns to
and a half seconds before it will read the same card. The LED flash is typically 250 milliseconds long.
The operation of the LED and beeper may be controlled by the Host, in which case the actual operation
will depend on the programmed timing of the Host.
1.2 Parts List
1.2
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
1.3 Regulatory Approvals and Certifications
1.3
§
HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA • Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
Проектирование. Монтаж. Продажа. - http://vskd.ru
Operation
Parts List
MaxiProx Reader
Installation Manual
Cable Fitting
Label for front cover - HID logo
#6-32 x 1" flat head screw, for upper-left base mount
screw
#6-32 x 1" black screw, for gang-box mounting
#6-32 x .75" flat head screw, for front cover mounting
Cable, 5 conductor, 22 AWG (Alpha 1295 C or
equivalent)
Power Supply – 2.0 A linear regulated
+12VDC Shunt Jumper – P2-1 to P2-2 for 12VDC
operation
Regulatory Approvals and Certifications
Underwriters Laborites listing
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
HID Technical Support
green
and the beeper sounds when the tra nsponder
red
. There is an anti-passback delay of about one
Qty 1 (included)
Qty 1 (included)
Qty 1 (included)
Qty 1 (included)
Qty 1 (included)
Qty 2 (included)
Qty 1 (included)
See cable notes
+24VDC, nominal (+21 TO 28.5VDC)
Factory Default – No P2 Shunt Jumper
For Europe, use ALTRONIX SMP3
(USER SUPPLIED TRANSFORMER AND
BATTERY)
+12VDC, nominal (+11.6 to +20.9VDC)
For Europe , use ALTRONIX SMP3
(USER SUPPLIED TRANSFORMER AND
BATTERY)
§
CE Mark
for
red
5 of 20
Page
Advertisement
Table of Contents
