Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Geoscan Pioneer
Summary of Contents for Geoscan Pioneer
- Page 1 GEOSCAN PIONEER Quadcopter Assembly and Operation Manual Ver. 2.0...
-
Page 2: Table Of Contents
Help the engineers make the product even better – give us your feedback and comments. Storage, transportation and disposal Li-Po batteries usage Join us! If something goes wrong YouTube Geoscan Pioneer Vkontakte Instagram account. Geoscan.aero forum. Pioneer page at Geoscan website channel. community. www.geoscan.aero/ru/pioneer/... -
Page 3: Introduction
Pioneer kit description, specification and figures included in the manual are relevant at the date of publication. Geoscan company reserves the right to change the product design and specification without notice. Pioneer quadcopter is a highly engineered product. For safe and fault-free operation, the rules set out in the Safety Guide must be Protection USB cable strictly observed. - Page 4 Frame Frame fixings Motors Remote control Receiver unit Studding nut (metal, short) (6 pc.) Battery compartment back plate RH rotation motor (2 pc.) Studding nut (long) (6 pc.) Studding nut (short) (6 pc.) Frame base Screw M2x4 (12 pc.) LH rotation motor (2 pc.) Screw M3x5 (6 pc.) Screw M3x10 (12 pc.) Battery compartment...
-
Page 5: Quadcopter Assembly
Quadcopter Assembly Prior to assembling the quadcopter, prepare a convenient Step 3 workplace. The kit includes many small parts, so take care not to lose them when assembling. Prepare: the unit assembled at Step 2, damper - 4 pc., screw Step 1 M3x10 - 4 pc. - Page 6 Step 7 Step 5 Prepare: the unit assembled at Step 6, studding nut (metal, short) - 4 pc., main board. Prepare: the unit assembled at Step 3, landing gear (upper part), Place the board onto the dampers so that the arrows on the landing gear (lower part), battery compartment back plate.
- Page 7 Step 11 Prepare: the unit assembled at Step 10, propeller 5030 - 2 pc., Step 9 propeller 5030R - 2 pc. Prepare: the unit assembled at Step 8, protection arch - 8 pc., Attention: the black nuts have a left-hand thread! Propeller protection bar - 8 pc., screw M3x10 - 8 pc., labels (5030 or 5030R) must correspond to labels on the frame.
-
Page 8: Control
In this manual, only controls needed to perform the Pioneer flight are described. In the case of using a quadcopter and a remote control unit... - Page 9 At SYSTEM tab: Battery installation If the binding is successful, the quadcopter should beep. Remote control unit setup 1. OUTPUT MODE → Output → PPM In case there is no beep, try to repeat the binding procedure Open battery compartment cover. 1.
-
Page 10: Preparation For Flight
Preparation for flight Control and flight modes Fully charge the quadcopter battery. Charge the battery Stabilization mode (SwC switch in upper position) according to the instructions given at page 24. Do not leave the battery connected to the charger unattended. Throttle stick controls motor power. -
Page 11: Flight
Flight To start the propellers, move the left stick (“throttle/heading») to the right and down, and hold it in this position until the propellers start. Perform the flight, controlling the quadcopter by sticks and mode switch. After landing, stop the propellers by moving the left stick (“throttle/heading») to the left and down, and hold it in this position until the propellers stop. - Page 12 Expand quadcopter functionality by using optional modules. Get new functionality. At present, the following optional modules for Pioneer quadcopter have been developed by Geoscan company: Follow the updates at https://www.geoscan.aero/ru/products/pioneer/. Update quadcopter firmware using the latest firmware version and the manual on update available on the website.
-
Page 13: Storage, Transportation And Disposal
The charger allows to charge 2- or 3-element the batteries from the control unit. accordance with local regulations, taking them to the nearest batteries. To charge 2-element Pioneer battery use the three- hazardous waste collection facilities. pin connector. The connectors have a guide pin to observe Keep the quadcopter in a dry place, away from heat sources, the polarity. -
Page 14: If Something Goes Wrong
If something goes wrong When connecting the battery the quadcopter does not react in any way. The battery may be low. Try to check the voltage. The voltage should not be lower than 6.4 V. Try to use a The quadcopter falls to the side when trying to take-off. different battery. - Page 15 © Geoscan, 2018 123242, Russia, Moscow Technical support: Bolshaya Gruzinskaya, 12, 8 800 333-84-77 build. 12 +7 931 208-60-22 194021, Russia, Saint-Petersburg support@geoscan.aero Shatelena str., 26А info@geoscan.aero...
Need help?
Do you have a question about the Pioneer and is the answer not in the manual?
Questions and answers