Advertisement
CONNECTIONS
Connections
Monitor
1
G C B
Flange-back adjustment
2
Digital video recorder
or time-lapse VCR
: VIDEO IN
: VIDEO OUT
1,4
CONNECTIONS
What you need
Peripheral equipment (such as monitor, digital video recorder or time-
lapse VCR)
Cables for connecting peripheral equipment and camera (coaxial cables,
connecting plugs)
Power adapter (24 V AC or 12 V DC)
Supported coaxial cables
You can use any of the following coaxial cables:
RG-59U (3C-2V) Length: About 250 m max.
RG-6U (5C-2V)
Length: About 500 m max.
RG-11U (7C-2V) Length: About 600 m max.
When using an RG-59U (3C-2V) cable, do not use it on piping or air
wiring.
Select the cable according to the distance between the devices you wish
to connect.
If you use a cable other than the types above, the image or sync signal
will be attenuated and will not be transmitted correctly.
Making connections
1
Connect the camera and peripheral equipment.
2
Connect the power cable.
<When using a 24 V AC adapter>
Connect 3 wire grounded cable (use 18AWG+) to the ground (GND)
terminal as shown in Figure 1.
<When using a 12 V DC adapter>
Connect the cable as shown in Figure 2.
When connecting the power cable to the camera, check that the polarity
is correct.
To prevent a fire hazard use any UL listed wire rated VW-1 for the 24 V
AC cable input terminal.
3
Insert the power adapter plug into the wall outlet.
The power indicator (POWER) lights.
Color/black and white setting
Connect each pin of the CONTROL terminal as indicated below, to set the
image to color or black and white manually. You can adjust the image by
remote control.
Color image setting
Connect the C (color) and the G (ground) pins.
Black and white setting
Connect the B (black and white) and the G (ground) pins.
24 V AC connection
12 V DC connection
GND
3
AC24V
GND
AC24V
DC12V
DC12V
2
2
Figure 1
Figure 2
Camera adjustment
Flange-back lock
VR302 VR303 VR301
screw
IRIS
AP
GAIN
BLC
WB SYNC C-BW
EI
SHRP
HI M
C M
LL
H
ON
1
2 3 4 5 6 7 8
3
INT
AI
NOR NOR OFF
ATW
L
Fig. A
CONTROL terminal
Image
C
B
OFF
OFF
Auto
OFF
ON
Black and white
ON
OFF
Color
ON
ON
Auto
ON: Close OFF: Open
The maximum length of cable for the CONTROL terminal is 400 m
(AWG24).
During optical filter switching, even if the manual switching operation is
complete, you cannot determine if the image is color or black and white.
Manual switching will have to be performed one more time.
FLANGE-BACK ADJUSTMENT
If the pick-up surface is not correctly positioned with relation to the lens
focal point, the picture will be out of focus (in particular when using auto-iris
power zoom lenses, sold separately). If that is the case, adjust the flange-
back position as described below.
1
Using a + screwdriver, loosen the flange-back lock screw (M2:+).
2
Set the zoom lens to the maximum telephoto position and set the
focus using the focus ring on the lens.
3
Set the zoom lens to the maximum wide angle position and set the
focus using the flange-back adjustment lever.
4
Repeat steps 2 and 3, until the image stays in focus when
changing from a telephoto shot to a wide angle shot.
When the setting is complete, tighten the flange-back lock screw.
When the flange-back lock screw is completely tightened it will protrude
slightly as shown in the illustration (Fig. A).
Do not tighten the screw further.
CAMERA ADJUSTMENTS/SETTINGS
The camera comes pre-adjusted and ready to install at time of factory
shipment, but you may want to make adjustments or settings to adapt to the
operating conditions or installation environment.
If you have trouble adjusting the camera, contact your place of purchase or
a Sanyo Authorized Service Center.
Iris setting
1
Change Iris setting when using either lens below.
EI
When using a manual or fixed iris lens and the electronic iris
(for indoor use)
function is on.
* Set the lens aperture to the shortest F stop.
AI
When using an auto-iris lens.
The electronic iris is suitable for normal indoor use. When switch 1 (IRIS)
is set to the up (EI) position, do not use an auto-iris lens.
If used under fluorescent light, the image may flicker. In such a case,
change to incandescent lighting or set switch 1 (IRIS) to the down (AI)
position and use an auto-iris lens.
When shooting bright subjects, pay attention to the light angle in order to
avoid or minimize the smear effect.
3
If conditions are outside the electronic iris operation range or more than
the maximum illumination, the CCD will be saturated. In that case, use
the auto iris lens.
Aperture (outline compensation)
If object outlines appear too strongly, set to "NORM".
SHRP
Emphasizes object outlines.
NORM
Normal setting
Gain control (AGC)
For adjusting the sensitivity of the camera. Use this setting for shooting in
dark environments.
HI
Increased sensitivity allows shots to be taken in dark
environments.
RED
BLUE L
H
NORM
Normal setting
LEVEL
The HI setting causes noise generation and a grainy image.
Backlight compensation
This camera has two different backlight compensation functions: Normally
CONTROL
backlight compensation switch
position. Change the backlight compensation switch settings depending on
the conditions.
G C B
4 5
When there
is backlight
in the entire
screen
4 5
When there
is backlight
only in the
background
SANYO INDUSTRIAL VIDEO
COLOR VIDEO CAMERA LIMITED WARRANTY
In order to obtain warranty service, the product must be delivered to and picked up from an
Authorized Sanyo Service Center at the user's expense, unless specifically stated otherwise in
this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained
by calling the toll-free number listed below.
For product operation, authorized service center referral, service assistance or problem
resolution, call
CUSTOMER INFORMATION 1-800-421-5013
Weekdays 8:30 AM – 5:00 PM Pacific Time
For accessories and/or parts, call
PARTS ORDER INFORMATION 1-800-726-9662
Weekdays 8:30 AM – 5:00 PM Pacific Time
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN
THE UNITED STATES OF AMERICA, EXCLUDING ALL U.S. TERRITORIES AND
PROTECTORATES. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL
PURCHASER OR END-USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR
RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE
CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company
warrants this SANYO product against defects in materials and workmanship for the periods
specified below. SFC will repair or replace (at its option) the product and any of its parts which fail
to conform to this warranty. The warranty period commences on the date the product was first
purchased or rented at retail.
LABOR
3 YEARS
White balance (color compensation)
MANU
Lets you fine-tune the white balance manually.
WB
ATW
Compensation is performed automatically.
Sync setting
Vertical sync disturbance may occur when a selector is used to switch
between multiple cameras connected to one monitor. To prevent vertical
sync disturbance, set to "LL."
2
LL (external sync)
INT (internal sync)
LL (Line-Lock): Synchronizes the unit with power frequency.
3
If image disturbance doesn't disappear after adjusting the PHASE dial on
the second and subsequent cameras, adjust the PHASE dial on the first
camera. If the problem persists, check that all the devices have been
connected with the correct power cable polarity.
Color/black and white switch setting
This switch lets you select the timing of the automatic switching of the
optical filter to color image or black and white image, according to the
3 4 4 5
subject brightness.
H
4
and
5
are set to the down (OFF)
L
When the power is turned off and then on, switching will restart from color.
Multi-spot metering
A sound of the optical filter may be heard when the color image or black
and white image is switched. Also, the image will be distorted (black lines
If the background of the object is
may appear on the screen). This is normal and does not indicate a
extremely dark, the center of the object
problem.
may be too bright. In this case, set
When using infrared lighting, and if there is a strong reflection on the
center-weighted metering mode.
subject, the optical filter may switch from black and white to color mode.
The focus setting may be different in color and black and white mode.
Center-weighted metering
Please check and adjust the focus setting in both modes.
Only the center of the image is metered
and backlight-compensated.
Iris dial (lens iris)
If the entire image is too dark or too bright, adjust the LEVEL dial (
L (Low)
4
5
Do not set switches
and
both to
"ON". Compensation will not be
H (High)
performed correctly with this setting.
This warranty does not cover (A) the adjustment of customer-operated controls as explained in
the appropriate model's instruction manual, or (B) the repair of any product whose serial number
has been altered, defaced or removed.
This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.
OBLIGATIONS
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or
reinstallation of the product after repair.
This warranty does not apply to repairs or replacements necessitated by any cause beyond the
control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting
from unauthorized service or parts, improper maintenance, operation contrary to furnished
instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse,
neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and
tear.
The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize
any party to assume for it any other obligation or liability.
SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO
THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN
NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY
DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO
CAUSES BEYOND ITS CONTROL. SFC'S LIABILITY FOR ANY AND ALL LOSSES AND
DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR IN
CONNECTION WITH THE SALE, USE OR OWNERSHIP OF THIS PRODUCT INCLUDING
WARRANTOR'S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIIVE GOODS, WHETHER
SUCH DEFECTS ARE DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
For your protection in the event of theft or loss of this product, please fill in the information below
for your own personal records.
Model No.
PARTS
IMAGE DEVICE
Date of Purchase
3 YEARS
3 YEARS
Where Purchased
5 6 5 9 5 10
• R (Red) dial
9
: Turn clockwise to augment screen red.
• B (Blue) dial
10
: Turn clockwise to augment screen blue.
7
Adjust PHASE dial to eliminate sync disturbance.
Internal Sync
8 8
For a brighter setting than L
Standard setting
5 1 1
11
).
Closes the lens iris, making the entire image darker.
Opens the lens iris, making the entire image brighter.
EXCLUSIONS
ATTENTION
Serial No.
(Located on back or bottom side of unit.)
Purchase Price
Advertisement
