Table of Contents
Advertisement
B B A A C C K K B B O O A A R R D D A A T T T T A A C C H H M M E E N N T T
I I M M P P O O R R T T A A N N T T : : Pole MUST be at
original 30º installation angle as
specified in Pole Assembly.
S S t t e e p p 1 1 : : Open lid of box containing
backboard 1 1 and position the
backboard (without removing it from
box) face down under lower
extension arm 2 2 with rim mounting
plate 3 3 toward pole.
N N O O T T E E : : Backboards are attached to
extension arms using the following:
P P r r o o 6 6 7 7 2 2 & & P P r r o o 6 6 6 6 0 0 : : Four 1/2" x 3-
1/4" bolts, eight flat washers and four
locknuts (#12 in parts list).
H H a a r r d d w w a a r r e e S S e e q q u u e e n n c c e e : : Bolt passes through flat
washer - arm bracket - backboard bracket -
arm bracket - flat washer - locknut.
P P r r o o 5 5 6 6 0 0 & & P P r r o o 5 5 5 5 4 4 : : Four 1/2" x 2-
1/2" bolts (#12 in parts list), eight flat
washers and four locknuts.
H H a a r r d d w w a a r r e e S S e e q q u u e e n n c c e e : : Bolt passes through flat
washer - arm - backboard bracket - flat washer
- locknut.
2 2 2 2
P P r r o o S S e e r r i i e e s s I I n n t t . . J J a a c c k k S S y y s s t t e e m m I I n n s s t t r r u u c c t t i i o o n n s s
6 6
w w w w w w . . p p r r o o f f o o r r m m a a n n c c e e h h o o o o p p s s . . c c o o m m
5 5
4 4
3 3
P P r r o o 4 4 5 5 4 4 & & P P r r o o 4 4 4 4 8 8 : : Two 1/2" x 8"
bolts (#12 in parts list), four 5/8" flat
washers and two 1/2" locknuts.
N N O O T T E E : : 5/8" washer needs to be
seated properly over nylon bushing
on outside of backboard H-frame.
H H a a r r d d w w a a r r e e S S e e q q u u e e n n c c e e : : Bolt passes through flat
washer - backboard bracket - extension arm –
extension arm – backboard bracket - flat
washer - locknut.
S S t t e e p p 2 2 : : Align lower backboard holes
4 4 with l l o o w w e e r r extension arm holes 2 2 .
Attach backboard to arm using
hardware noted above.
S S t t e e p p 3 3 : : Align upper backboard holes
5 5 with u u p p p p e e r r extension arm holes 6 6 .
Attach backboard to arm using
hardware noted above.
N N O O T T E E : :
P P r r o o 6 6 7 7 2 2 & & P P r r o o 6 6 6 6 0 0 : : Do not over
tighten. Snug tighten only.
P P r r o o 5 5 6 6 0 0 & & P P r r o o 5 5 5 5 4 4 : : Do not over
tighten. Tighten so that bushings in
arms meet bushings in backboard.
1 1
2 2
1 1 . . 8 8 8 8 8 8 . . 3 3 5 5 3 3 . . 4 4 6 6 6 6 7 7
Advertisement
Table of Contents
