PROformance Hoops Pro Series Installation & Owner's Instructions page 21

P P r r o o S S e e r r i i e e s s I I n n t t . . J J a a c c k k S S y y s s t t e e m m I I n n s s t t r r u u c c t t i i o o n n s s
P P O O L L E E A A S S S S E E M M B B L L Y Y ( ( c c o o n n t t i i n n u u e e d d ) )
7 7
6 6
S S t t e e p p 7 7 : : P P r r o o 6 6 7 7 2 2 , , P P r r o o 6 6 6 6 0 0 , , P P r r o o 5 5 6 6 0 0 & & P P r r o o
5 5 5 5 4 4 O O n n l l y y
Position lower extension arm 1 1 with clevis
2 2 toward pole offset. Align lower extension
arm pivot holes with lower holes 3 3 in
pole.
S S t t e e p p 7 7 : : P P r r o o 4 4 5 5 4 4 & & P P r r o o 4 4 4 4 8 8 O O n n l l y y
Position lower extension arm with gusset
4 4 away from pole offset. Align lower
extension arm pivot holes with lower holes
5 5 in pole.
S S t t e e p p 8 8 : : Attach lower extension arm to pole
using the following:
P P r r o o 6 6 7 7 2 2 & & P P r r o o 6 6 6 6 0 0 : : 3/4" x 10-7/8" pin and two
lock collars (#8 in parts list). Tighten with 5/32"
hex key (provided).
P P r r o o 5 5 6 6 0 0 & & P P r r o o 5 5 5 5 4 4 : : 5/8" x 8-1/2" bolt (#8 in
parts list), two flat washers and locknut.
P P r r o o 4 4 5 5 4 4 & & P P r r o o 4 4 4 4 8 8 : : 5/8" x 7-1/2" bolt (#8 in
parts list), two flat washers and locknut.
N N O O T T E E : : On the Pro 560, Pro 554, Pro 454 &
Pro 448 models, tighten so that bushings
on extension arms meet bushings in pole.
S S t t e e p p 9 9 : : Attach upper extension arm 6 6
pivot holes with upper holes 7 7 in pole.
1 1 . . 8 8 8 8 8 8 . . 3 3 5 5 3 3 . . 4 4 6 6 6 6 7 7
3 3
1 1
w w w w w w . . p p r r o o f f o o r r m m a a n n c c e e h h o o o o p p s s . . c c o o m m
5 5
2 2
4 4
Contender & Champion Only
Attach arm to pole using the following:
P P r r o o 6 6 7 7 2 2 & & P P r r o o 6 6 6 6 0 0 : : 3/4" x 10-7/8" pin and two
lock collars (#8 in parts list). Tighten with 5/32"
hex key (provided).
P P r r o o 5 5 6 6 0 0 & & P P r r o o 5 5 5 5 4 4 : : 5/8" x 8-1/2" bolt (#8 in
parts list), two flat washers and locknut.
P P r r o o 4 4 5 5 4 4 & & P P r r o o 4 4 4 4 8 8 : : 5/8" x 7-1/2" bolt (#8 in
parts list), two flat washers and locknut.
N N O O T T E E : : On the Pro 560, Pro 554, Pro 454 &
Pro 448 models, tighten so that bushings
on extension arms meet bushings in pole.
S S t t e e p p 1 1 0 0 : : Attach upper mount of jack to
lower extension arm using the following:
P P r r o o 6 6 7 7 2 2 & & P P r r o o 6 6 6 6 0 0 : : 1" x 2-1/4" pin, two nylon
washers, two fender washers, and two 1/2"
socket screws (#10 in parts list). Tighten with
5/32" hex key (provided).
P P r r o o 5 5 6 6 0 0 & & P P r r o o 5 5 5 5 4 4 : : 5/8" x 2-1/4" bolt
(#10 in parts list) and locknut.
P P r r o o 4 4 5 5 4 4 & & P P r r o o 4 4 4 4 8 8 : : 5/8" x 8" bolt
(#10 in parts list), two flat washers and locknut.
N N O O T T E E : : On the Pro 560, Pro 554, Pro 454 &
Pro 448 models, do NOT over tighten.
Snug tighten only.
2 2 1 1