Table of Contents
Advertisement
6. connecTing a rain sensor
An...interrupt...type,...normally...open...rain...sensor...can...be...connected...to...the...controller....the...
sensor...connects...directly...to...the...controller...sensor...terminals.
connect...either...wire...from...sensor...to...the...two...sensor...terminals...on...the...controller...(see...
figure...1)....Follow...the...sensor...manufacturer's...instructions...for...calibrating...the...sensor....
See...section...16...for...sensor...setup.
7. Programming
dIG...controllers...are...programmed...with...the...aid...of...four...buttons:
Programming...step...selector...–...used...to...select...the...
desired...programming...mode...(included...clock...
...
setting...mode)
... d ata...increment...button...(decrease)...–...Lowers...the...
value...of...the...selected...parameter...(e.g.,...when...
hours...selected,...from...06:00...to...05:00).
data...increment...button...(Increase)...–...raises...the...
value...of...the...selected...parameter...(e.g.,...when...
...
hours...selected...from...06:00...to...07:00).
next...step...button...–...used...to...select...the...parameter...
to...be...changed...(hour,...minute,...etc.)....only...a...
...
blinking...parameter...can...be...changed.
8. seTTing currenT Time and day of The week
to...enable...the...controller...to...operate...the...system...
at...the...correct...times,...the...current...time...and...
current...day...of...the...week...must...first...be...set....Steps...
below...explain...how...to...set...the...day...and...time,...
Press...the...
...hour...digit...will...blink....use...the...
or...
,...to...set...the...current...hour...(note:...use...of...AM...and...PM...designations)....Press...
minutes...digit...blink,...set...the...current...minute...using...
arrow...will...appear...in...the...upper...portion...of...the...display....use...the...
the...arrow...to...current...day....Press...
...to...proceed...to...the...next...step.
Note: If the last data entered stops flashing, press the
resume programming.
5004..................................................................5006-IP... ... ... ... ... ... ... ... ... ... ...
...
...or...
....Press...
...A...blinking...
...or...
...to...move...
again to
4
9. Time formaT (swiTching beTween am/Pm & 24 hour)
the...default...time...format...is...AM/PM....there...is...also...a......
24...hour...time...format...option...that...can...be...switched......
between...the...two...formats.
Press...
...several...times...until...
Press...
...hour...digit...will...blink....Press...the...
...simultaneously....the...clock...reading...switches...from...AM.../PM...to...a...24...hour...time...
display...or...vice...versa.
Note: You can switch the time display format at any step in the
programming process.
10. valve selecTion
First...select...the...desired...valve,...and...then...schedule...as...follows:
Press...
...until...
...appears....
Press...
....A...blinking...arrow...appears...at...the...bottom...
of...the...display....Move...the...arrow...to...the...desired...valve...
number...by...pressing...
proceed...to...the...next...step.
11. seTTing waTering Time
this...setting...determines...the...duration...of...time...that...
the...valve...will...remain...open....In...this...option...choose...
hour,...minute...or...second...(seconds...available...only...on...
model...5006-IP...propagation...controller).
Press...
...until...
...appears....Press...
...the...
digit...blinks....Set...the...desired...number...of...hours...by...
pressing...
...or...
....Press...
number...of...minutes...by...pressing...
......appears....
...and...
...or...
....Press...
...to...
,...the...hour...
...again,...the...minute...digits...blink....Set...the...desired...
...or...
....Press...
...to...proceed...to...the...next...step.
5
Advertisement
Table of Contents
