Setting The Clock; Using An Usb Device - LG XA64 Owner's Manual

XA64-D0U-AGBRLL-ENG 7/8/10

Setting the Clock

1. Turn the power on
2. Press for at least 2 seconds
3. Choose from either: AM 12:00 (for an am and pm
display) or 0:00 (for a 24 hour display).
4. Confirm your selection
5. Select the hours
6. Press
7. Select the minutes
8. Press: The clock setting is finished.
Using your player as an alarm clock
1 Turn the power on.
2 Press and hold TIMER Each function, EX) TUNER, CD.... flashes.
3 Press SET when the function you want to be woken by is showing.
4 Choose one of them by pressing SET.
5 "ON TIME" will be displayed. Then you can set the time you want the alarm to
go on. Press ./> to change the hours and minutes and SET to save.
6 "OFF TIME" will be displayed. Then, you can set the time you want the
function to stop. Press ./> to change the hours and minutes and
press SET to save.
7 You will be shown the volume (VOL) you want to be woken by.
Use ./> to change the volume and SET to save.
The clock icon " " shows that the alarm is set.
8 Press TIMER button 2times. You can check the setting status.
Notes:
• If you set the clock time, you can check the time by pressing CLOCK even
when the player is turned off.
• If you set the clock time and alarm, you can check the alarm icon "
pressing CLOCK even when the player is turned off.
Setting the asleep time
1 Press SLEEP repeatedly to select delay time between 10 and 90 minutes,
after the unit will be turned off.
2 To check the remaining time, press SLEEP.
3 Press SLEEP once while "SLEEP 10" is displayed, to deactivate sleep function.
DIMMER
Press SLEEP once. The LED (Light-emitting diode) of front panel is turned off
and the display window will be darken by half. To cancel it, press SLEEP
repeatedly until dim off.
10:15 AM Page 9
ON UNIT
1 1 /] ]
CLOCK
./>
SET
./>
SET
./>
SET
" by

Using an USB device

You can enjoy media files saved on an USB device by connecting the
USB device to the USB port of the unit. For [Creating your own playlist]
and [Random/Repeat play], refer to the CD playback section.
1. Connect the USB device to the
USB port of the unit.
2. Select the USB function.
3. Select a file you want to play.
4. Start your media playing.
5. To stop, press
6. Before disconnecting the
portable USB device, change to
any other function.
Compatible USB Devices
• MP3 Player : Flash type MP3 player.
• USB Flash Drive : Devices that support USB 2.0 or USB 1.1.
• The USB function may not be available depending on devices.
• Devices which require additional program installation when you have
connected it to a computer, are not supported.
Look out for the following
• Do not extract the USB device while in operation.
• For a large capacity USB, it may take longer than a few minute to be
searched.
• To prevent data loss, back up all data.
• If you use a USB extension cable or USB hub, the USB device is not
recognized.
• Using NTFS file system is not supported. (Only FAT(16/32) file system is
supported.)
• This unit is not supported when the total number of files is 1000 or more.
• External HDD, Locked devices or hard type USB devices are not supported.
• USB port of the unit can not be connected to PC. This unit can not be used
as a storage device.
ON UNIT ON REMOTE
-
-
FUNCTION
FUNC.
. / >
. >
. b b b b / B B B B > . >
B B []
B B / []
x x STOP
x x
FUNC.
FUNCTION
9