Kohler K-702200 Installation And Care Instructions

Sliding Bath Doors Sliding Shower Doors
USA/Canada: 1-800-4KOHLER
México: 001-800-456-4537
Critical Information!
Read Before Installation!
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
IMPORTANT! Do not touch the edges of the tempered glass with tools or
any other hard objects. Do not set the unframed tempered glass directly on
the floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
IMPORTANT! Do not cut the top track the same length as the bottom track.
NOTICE: The warranty does not apply to a product that has been modified
or altered in a manner other than as expressly permitted in the Installation
and Care Guide.
Walls must be within 3/8" (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer's instructions for application and
curing time.
To watch this installation online, visit the product page at
www.kohler.com.
For care and cleaning and other information; visit
http://www.kohler.com/clean.
Read and follow all instructions.
Measure distance "A." Subtract 1/4" (6 mm) or
1
the width of a number 2 pencil from "A" and cut
the bottom track.
A
1/4" (6 mm)
"A" Mark
Cut Line
A
Remove the wall jambs. Drill 5/16" holes into
6
the walls and insert the anchors.
x2
3
2
1
1204880-2-D
Required Tools
kohler.com
1/16"
Center Punch
Number 2 Pencil
Tin Snips 3/16" 5/16"
5/16" Masonry Bit for Tile
100% Silicone Sealant Masking Tape
32 Teeth Per Inch Blade Miter Box
Position the bottom track on the center of the
2
ledge. If needed, file the ends to match the
corners.
Apply silicone sealant in the groove on the
7
underside of the bottom track. Secure the bottom
track to the ledge along the marked location.
Groove
K-702200, K-702202, K-702204, K-702206, K-702208, K-702211, K-702213, K-702215, K-702219, K-702221
Parts Identifi cation
1205305**
Hanger Bracket Kit
Model Number Label
1203635**
Hardware Skin Pack
Inside Panel*
Wall Jamb*
1031943**
Screw Cover
Wall Jamb
Notch
Center the bottom track on the ledge with the
3
bottom track leg to the outside. Tape the bottom
track in place and mark the position.
Bottom-Track
Leg
Tile Installations Only
8
Nick the tile at the mark for the hole before
drilling with a center punch. This keeps the drill
bit from moving as the hole is started.
When installing to a tile wall, first drill a small
diameter hole, then a larger hole.
Install anchors. Do not install the screws directly
into the tile, as this may crack the tile.
When drilling, use a masonry bit.
Mark
Center
Punch
1
Installation and Care Instructions
*Need help? Contact the KOHLER Customer Care Center
Top Track*
#8-32 x 3/8"
1199426-01**
Hanger Bracket
1199110
Gasket
1050048-B
Barrel Nut
1077763-A
Bolt
1048208-B (Silver)
1048208-K (Brass)
Screw
1017813-01** (K-702200, K-702204, K-702206)
1017813-02** (K-702208)
1017813-03** (K-702202)
1017813-05** (K-702211, K-702221)
1017813-06** (K-702213)
1017813-07** (K-702215)
1017813-08** (K-702219)
Inside-Panel Guide
IMPORTANT! The bottom track and wall jamb
4
must sit flat against the shower ledge and the
wall. If needed, trim and file the wall jamb. Use
a coin to match and to transfer the corner radius
of the shower to the wall jamb.
Notch
Reposition both wall jambs. Secure the wall
9
jambs with screws. Attach a bumper at the top
and bottom locations.
x2
Screw Cover
#8-18 x 1-1/2"
Screw Cover
Sliding Shower and Bath Doors
at 1-800-4KOHLER (1-800-456-4537).
For service parts information, care and cleaning, and
other information, visit www.kohler.com/serviceparts.
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
1051142-A
Screw
1044585
Roller
Wall Jamb*
Outside Panel*
1131838**
Bumper
8-32 x 1/4"
1077762
Anchor
Towel Bar
#8-18 x 1-1/2"
(Includes
1048208-C (Silver)
Hardware)*
1048208-F (Brass)
Screw
1031943**
Screw Cover
Wall Jamb
Notch
#8-18 x 3/8"
10070.45 (Silver)
10070.46 (Brass)
10070.30 (Nickel)
10070.72 (Bronze)
Bottom Track
Position the wall jambs over the bottom track.
5
Plumb both wall jambs. Mark the screw holes.
x2
Check the bumpers for the correct horizontal
10
alignment with the wall jambs.
Correct Incorrect