Advertisement
Quick Links
BEFORE YOU BEGIN
BEFORE YOU BEGIN
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
·
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
·
These instructions contain important care, cleaning,
and warranty information-
instructions for the consumer.
·
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
·
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 3 for reference.
·
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
· The product complies with QB 2584-2007.
CAUTION: Risk of injury or product damage.
Tempered glass cannot be cut, drilled or
knocked by hard object. Make sure corner area
of the glass refraining from knocking so as to
cause personal injury due to broken glass.
ATTENTION:
Please install this door on Kohler
receptors or curbs(Not included). If the curb is not
Kohler-branded, please note its top width should be
more than 80mm.
IMPORTANT:
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won't take responsibility of the installation
quality.
ZHONGSHAN KOHLER SHOWER CO., LTD.
DEVELOPMENT ZONE, ZHONGSHAN, GUANGDONG, CHINA
1280147-T01-A
please leave these
SLIDING, SCR BYPASS (W/O STO), 8mm
SLIDING, SCR BYPASS (W/O STO), 10mm
·
·
·
·
·
·
·
QB 2584-2007
)
3mm/m
NO13-1, XINYE ROAD, ZHONGSHAN TORCH
13-1
©
Copyright Kohler China Investment Co., Ltd. 2016
-1-
©
SKYLINE
INSTALLATION INSTRUCTIONS
(
K-705879T-FM-SHP
(
K-81515T-FM-SHP
3
80mm
POST CODE: 528437
528437
) 8mm
) 10mm
(
2016
Advertisement
Related Manuals for Kohler SKYLINE K-705879T-FM-SHP
Summary of Contents for Kohler SKYLINE K-705879T-FM-SHP
- Page 1 · · All information is based on the latest product information available at the time of publication. Kohler China Ltd. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. · ·...
-
Page 2: Parts Identification
ROUGHING-IN Unit: mm K-81515T 1100-2050 1850-2000 K-705879T PARTS IDENTIFICATION PARTS IDENTIFICATION IMPORTANT Before installation check that all components are correctly supplied. If any parts are missing please ring the helpline. 800-820-2628 800-820-2628 1280147-T01-A... - Page 3 Top Rail, Skyline Bypass Insert Seal, Skyline Bypass Top Roller Assy, Skyline Bypass Wall, Skyline Bypass Cover Seal Wall Jamb, Skyline Bypass Door Glass, Skyline Bypass Side Metal Handle, Skyline Long Bottom Roller Assy, Skyline Bypass Bottom Rail, Skyline Bypass Short Bottom Roller Assy, Skyline Bypass Top Rail, Skyline Bypass...
- Page 4 INSTALLATION REQUIREMENTS INSTALLATION REQUIREMENTS Tools Required · · Phillips Screwdriver · · Pencil · · Caulk Gun · · Measuring Tape · · Safety Glasses · Center Punch · · Hammer · · Knife · · Masonry Drill & 6mm Drilll Bit ·...
- Page 5 Fix wall jambs. One is fixed on the wall. The other is not fixed on the wall after the holes are drilled. Pay special attention to both sides of the wall jamb(see magnified pictures below). Inside The wall jamb must Outside be kept vertical.
- Page 6 Insert the unfixed wall jamb into the frame. Then insert the whole wall jamb and fix the unfixed wall jamb. Insert the unfixed wall jamb. The wall jamb must be kept vertical. STEP Adjust the top and bottom frames vertical. The length shall be the same on two sides. Then rotate the lock to fix wall jamb.
- Page 7 Install top rollers. The caps shall be installed after the door glass is adjusted. STEP Install door glass. Note: Install outside door glass first and then inside door glass. Adjust the height of door glass by adjusting the screws with cross screwdriver.
- Page 8 Install and adjust handle. Install handle. STEP Apply silicone sealant to both sides of the bottom Do not use the enclosure for at least 24 hours. threshold. 24hrs STEP STEP 1280147-T01-A...