Advertisement
PAGE II
5. SAFETY NOTES
Please take the time to read these instructions carefully and keep them
to hand in the intended storage compartment
on the child safety seat
14
at all times. The instructions must be kept with the child safety seat if the
latter is passed on to a third party.
DANGER! For the protection of your child:
• In the event of an accident with a collision speed of more than 10 km/h, the
child safety seat may be damaged without the damage becoming immediately
visible. In this case the child safety seat must be replaced. Please dispose of
it properly.
• As a rule, have your child safety seat checked if it was damaged (e.g if it falls
on the ground).
• Regularly check all important parts for damage. Ensure that all mechanical
parts, in particular, are fully functional.
• Never lubricate or oil parts of the child seat.
•
Never leave your child unattended in the child seat in the vehicle.
• Only allow your child to enter and exit the vehicle on the pavement side.
• Protect the child safety seat from intensive direct sunlight when it is not in use.
The child safety seat can get very hot in direct sunshine. Children's skin is
sensitive and could be harmed as a result.
• The more snugly the belt fits over your child's body, the better they will be pro-
tected. Therefore, avoid putting thick clothes on your child under the belt.
• Take regular breaks on long journeys in order to give your child the opportu-
nity to run about and play.
• Use on the rear seat: Move the front seat far enough forwards to ensure that
your child's feet cannot hit the backrest of the front seat (to prevent the risk of
injury).
DANGER! For the protection of all vehicle occupants:
In the case of an emergency stop or an accident, unsecured persons or ob-
jects may cause injury to other vehicle occupants. Please always check that...
• no other load-bearing contact points are used other than those specified in
these instructions and marked out on the child safety seat.
• the backrests of the vehicle seats are locked (i.e. that a foldable rear seat
bench latch is engaged).
• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are
secured.
• all persons in the vehicle have their seatbelts fastened.
• the child safety seat is always secured when it is in the vehicle, even if no child
is being transported.
WARNING! For your protection when handling the child seat:
• Never use the child safety seat free-standing, not even for test sitting.
• To avoid damage, ensure that the child safety seat is not jammed in between
hard objects (car door, seat rails, etc.).
• Keep the child safety seat in a safe place when it is not in use. Do not place any
heavy objects on the seat and do not store it directly next to sources of heat or
in direct sunlight.
CAUTION! To protect your vehicle:
• Certain car seat covers made from more sensitive materials (e.g. velour,
leather, etc.) may sustain signs of wear and tear when using child safety seats.
For optimum protection of your car seat covers, we recommend using the
BRITAX RÖMER car seat protector from our range of accessories.
6. PREPARATORY WORK
01
02
1. If your vehicle is not fitted with ISOFIX insertion aids by standard, clamp the
two insertion aids
02
, which are included in the scope of delivery of the
seat*, with the section pointing upwards to the two ISOFIX fastening points
01
of your vehicle.
TIP: The ISOFIX fastening points are located between the surface and the
backrest of the vehicle seat.
2. Move the headrest of the vehicle seat into the top position.
* The insertion aids facilitate the installation of the child safety seat with the use of the
ISOFIX fastening points and prevent damage to the car seat covers. As long as they are
not used, remove them and keep them in a safe place. For vehicles with a foldable back-
rest, the insertion aids need to be removed before folding the backrest. Any problems
occurring usually come from soiling or external objects on the insertion aids and on the
hook. Remove soiling or external objects to rectify such problems.
7. INSTALLATION OF THE CHILD SAFETY SEAT
1. PREPARING THE ISOFIX
1
1.1 Pull the grey fabric loop
, until the ISOFIX
15
15
locking arms
16
are fully extended.
1.2 Push the green safety button
06
release button
05
on both sides of the seat
towards each other. This ensures that both
hooks on the ISOFIX locking arms
16
open and ready to use.
2. PREPARING THE TOP TETHER
2
13
13
2.1 Remove the top tether
from the user and
operating instructions compartment
22
place it over the child safety seat.
TIP: Only remove the red rubber band if the
length of the top tether
13
is not sufficient for
your vehicle model.
2.2 Place the child seat facing forward (in the
direction of travel) on a suitable vehicle seat.
Adjust the backrest angle of the car seat so
that the gap between the car seat and the
child safety seat is as small as possible.
2.3 Take the top tether
13
and press the metal
tongue
26
away from the harness in order
to make the harness longer and pull the top
tether
on the snap-in hook
13
22
forms a V shape.
2.4 Guide the top tether
13
on the left and right
side up to the headrest.
3. FASTENING THE TOP TETHER
3
Fit the snap-in hook
into the top-tether
22
22
anchoring point recommended in your vehicle's
operating instructions.
CAUTION! Make sure that you do not use
a
the luggage hooks instead of the top-tether
anchoring points. Look for the following symbol
b
c
in your vehicle:
4. FASTENING THE ISOFIX
4
4.1 Position the two ISOFIX locking arms
directly in front of the two insertion aids
4.2 Push both ISOFIX locking arms
16
02
insertion aids
until the ISOFIX locking
02
arms
engage on both sides with a click-
16
ing sound.
16
DANGER! The green safety button
must be visible on both sides so that the
child safety seat is correctly fastened.
5. PUSHING THE CHILD SAFETY SEAT UNTIL
5
SECURE
Push the child safety seat firmly backwards as far
as it will go.
6. CHECKING THE FASTENING
6
Shake the child safety seat to ensure that it is
securely fastened and check the safety buttons
06
to make sure that the two indicators are fully
on in green.
06
7. TENSIONING THE TOP TETHER
7
Tighten the belt strap of the top tether
23
the belt tension indicator
23
turns green and the
13
top tether
is taut.
13
8. SECURING YOUR CHILD
Carry out the steps specified in Section 8, "US-
ING THE CHILD SAFETY SEAT".
8. USING THE CHILD SAFETY SEAT
1. LOOSENING THE SHOULDER STRAPS
To loosen the shoulder straps, press the adjust-
ment button
09
and the red
07
shoulder straps
IMPORTANT! Do not pull the shoulder
08
pads
07
.
are
16
09
2. OPENING THE HARNESS BUCKLE
To open the harness buckle
and
14
button on the harness buckle.
04
3. POSITIONING CHILD IN THE SEAT
Place your child in the child safety seat.
Make sure that the buckle
and place your child in the child safety seat.
08
until it
4. FITTING THE SHOULDER STRAPS
04
Lay the shoulder straps
shoulders.
WARNING! Do not twist or swap the shoulder
straps, as this will invalidate the protective function.
5. ADJUSTING THE HEADREST
A correctly adjusted headrest
03
mum protection for your child in the child safety
seat:
The headrest
03
must be adjusted so that the
shoulder straps
08
08
child's shoulders or slightly higher.
►The shoulder straps
16
they run horizontally or just above your child's
02
.
shoulders.
into the
►The shoulder straps
behind your child's back, or level with/above their
ears.
06
To adjust the headrest:
5.1 Pull the adjusting ring
12
upwards.
5.2 Move the headrest
03
der strap height and make sure it is correctly
fastened by moving the headrest
slightly.
6. FASTENING THE HARNESS BUCKLE
Bring the two buckle tongues
terlock them before inserting them into the harness
04
buckle
04
– you must be able to hear a "click"
noise when doing this.
24
7. TENSIONING THE ADJUSTING STRAP
Pull the adjusting strap
and snug on your child's body.
WARNING! The hip belt must lie as low as pos-
10
sible over your child's groin.
13
, until
Before each car journey, in order to ensure your child's
safety, make sure that:
• the child safety seat is fastened in the ISOFIX fastening points
sides with the ISOFIX locking arms
and both safety buttons
16
completely green
• the child safety seat is securely fastened
• the top tether
is taut over the backrest of the car seat and the
13
belt tension indicator
• the harness of the child safety seat is fitted snugly to the child's
body without being constricting
and, at the same time, pull both
• the shoulder straps
forward.
08
not twisted
• the shoulder pads
body
• the buckle tongues
DANGER! If your child tries to open the ISOFIX safety buttons
harness buckle
stop as soon as possible. Check whether the child safety
04
04
, press the red
seat is correctly fastened and ensure that your child is correctly secured.
Explain to your child the dangers associated with their actions.
9. ADJUSTING THE SEAT ANGLE
The seat shell of the
TRIFIX i-SIZE
tions:
04
is folded forwards
09
08
over your child's
17
ensures opti-
03
If you have any further questions regarding the use of the carrier,
please feel free to contact us:
BRITAX RÖMER
Kindersicherheit GmbH
are at the same level as your
Theodor-Heuss-Straße 9
89340 Leipheim
Germany
BRITAX EXELSIOR
08
must be adjusted so that
LIMITED
1 Churchill Way West
Andover
Hampshire SP10 3UW
are not allowed to run
08
United Kingdom
10. REMOVING THE CHILD SAFETY SEAT
12
of the head rest
03
1. Loosen the top tether
03
to the correct shoul-
harness.
2. Unhook the snap hook
03
down
the top tether
13
to the front over the child safety seat.
3. Loosen the ISOFIX fastening on both sides by pressing the green safety
button
and the red release button
06
4. Pull the seat forwards and stow the top tether
tions compartment
5. Move the ISOFIX locking arms
24
together and in-
TIP: The ISOFIX locking arms are protected against damage once they are
put back into the seat bottom.
DANGER! Remove the child safety seat from the vehicle. Never transport
the child safety seat in the car if it is not fastened properly.
10
until the strap lies flat
11. DISPOSAL
Please observe the waste disposal regulations in your country.
Disposal of packaging
Seat cover
Plastic parts
Metal parts
on both
01
Belt straps
are
06
Buckle and tongue
is green
23
are correctly adjusted and the straps are
08
are in the correct position on your child's
07
are fastened into the harness buckle
.
24
04
06
or the
can be used in three different reclined posi-
To adjust the seat angle:
Push up the adjusting handle
09
and pull / slide the
seat shell
17
into the desired position.
DANGER! The seat shell
must engage se-
17
curely regardless of its position. Pull up on the seat
shell
17
to ensure that it is engaged.
TIP: You can even adjust the reclined position of
the seat shell
17
while your child is sitting in the
child safety seat.
T.: +49 (0) 8221 3670 -199/-299
F.: +49 (0) 8221 3670 -210
E.: service.de@britax.com
www.britax.com
T.: +44 (0) 1264 333343
F.: +44 (0) 1264 334146
E.: service.uk@britax.com
www.britax.com
by pushing away the metal tongue
from the
13
26
22
from the anchoring point in the vehicle and lay
towards each other.
05
in the operating instruc-
13
14
.
16
back into the seat shell
17
.
Container for cardboard boxes
Residual waste, waste incineration
To be placed in the corresponding
container according to labelling
Container for metals
Container for polyester
Residual waste
Advertisement
