AT&T CL83107 Quick Start Manual

CL83107/CL83207/CL83307/
This quick start guide provides you
CL83407
with basic instructions only. For
more complete instructions, refer
to your Abridged user's manual
provided in the package, or see the
online Complete user's manual at
www.telephones.att.com/manuals.
Quick start guide
Part lists
Ì
1 for CL83207
Ì
2 for CL83307
Ì
3 for CL83407
Install
Telephone base
Notes:
Ì
Plug one end of the telephone line cord into a telephone jack or a DSL
filter.
Ì
If you have DSL high-speed Internet service, a DSL filter (not included)
is required.
Charger
Caution: Use only the power adapter(s) provided with this product.
To obtain a replacement, visit our website at
www.telephones.att.com
or call
1 (866) 288-4268
Canada, dial
.
Battery
Install the battery, as shown below. Charge your handset(s)
before initial use. The battery is fully charged after ten hours
of continuous charging.
THIS SIDE UP /
CE CÔTÉ VERS LE HAUT
Ì
1 for CL83107
Ì
2 for CL83207
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT183342/BT283342 (2.4V 400mAh Ni-MH) Ì
WARNING / AVERTISSEMENT : 3 for CL83307
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1535
Ì
4 for CL83407
CL83107/CL83207/CL83307/
CL83407
Quick start guide
Caution: Use only the supplied rechargeable battery or replacement
battery (model BT183342/BT283342).
Overview
Handset
Handset
Ì
CHARGE light On when the handset is charging in
the telephone base or charger.
Ì
PUSH TO TALK Press to initiate a one-to-one or
one-to-group broadcast.
Ì
Press and hold to broadcast to a
group of system devices.
Ì
Press repeatedly to view the last
Redial
PAUSE ten numbers dialed.
Ì
While entering numbers, press and
hold to insert a dialing pause.
1 (800) 222-3111
. In
Ì
MENU When the handset is not in use,
SELECT press to show the menu.
Ì
While in the menu, press to select
an item or save an entry or setting.
Ì
Press to make or answer a call.
FLASH
Ì
During a call, press to answer an
PHONE
incoming call when you receive a
call waiting alert.
Ì
During a call, press to hang up.
CANCEL
Ì
While in a menu, press to cancel an
OFF
operation, back up to the previous
menu, or exit the menu display; or
press and hold this button to exit
to idle mode.
Ì
DIR Press DIR to show directory entries
when the handset is not in use.
Ì
Press to scroll up or down while in
menus.
Ì
Press to increase or decrease the
listening volume when on a call.
Ì
CID Press CID to show caller ID log
when the handset is not in use.
Ì
Press and hold to set or dial your
1
voicemail number.
Ì
Press to switch to tone dialing
temporarily during a call if you
have pulse service.
Ì
While entering names, press to
change the next letter to upper or
lower case.
Ì
Press and hold to enter the
QUIET mode setting screen, or to
deactivate QUIET mode.
Ì
Press to make or answer a call
using the speakerphone.
Ì
During a call, press to mute the
MUTE
microphone.
DELETE
Ì
Press to delete digit or character.
Telephone base
Handset
Ì
CALL BLOCK Press to block the incoming call
when the telephone is ringing.
Ì
When on a call, press to block the
call.
Ì
When the handset is not in use,
press to show the call block menu.
Telephone base
Ì
MIC Microphone
Ì
While in idle mode, press to
VOL / VOL
adjust the base ringer volume.
Ì
During message playback,
press to adjust the listening
volume.
Ì
IN USE indicator On when the telephone is in
use, or when the answering
system is answering an
incoming call.
Ì
Flashes when another
telephone is in use on the
same line.
f
CANCEL
While in a menu, press to
cancel an operation, back up
to the previous menu or exit
the menu display; or press and
hold to go back to idle mode.
f
When the telephone base is
ringing, press to mute the
ringer temporarily.
f
When the telephone base is
not in use, press and hold to
erase the missed call indicator.
Ì
FLASH/PTT Press to initiate a one-to-one
or one-to-group broadcast.
Ì
Press and hold to broadcast
to a group of system devices.
Ì
During a call, press to answer
an incoming call when you
receive a call waiting alert.
Ì
While the phone is idle, press
/ FIND HS
to page all handsets.
Ì
Press DIR to show directory
DIR
entries when the telephone
base is not in use.
Ì
Press CID to show caller ID log
CID
when the telephone base is
not in use.
Ì
MENU/SELECT When the telephone base is
not in use, press to show the
menu.
Ì
While in the menu, press to
select an item or save an
entry or setting.
Telephone base
Ì
Press to block the incoming
/
CALL BLOCK
call when the telephone is
ringing.
Ì
When on a call, press to block
the call.
Ì
When the telephone base is
not in use, press to show the
call block menu.
Ì
REDIAL/PAUSE Press repeatedly to view the
last ten numbers dialed.
Ì
While entering numbers, press
and hold to insert a dialing
pause.
Ì
Press to turn the built-in
/ ANS ON/OFF
Answering System on or off.
Ì
During playback, press to
/ REPEAT
repeat the playing message.
Ì
During playback, press twice
to play the previous message.
Ì
/ SKIP Press to skip a message.
Ì
Press to start or stop
/PLAY/STOP
Message Playback.
MUTE/DELETE Ì
During a call, press to mute
the microphone.
Ì
Press to delete digit or
character.
Ì
Press to delete the message
currently playing.
Ì
Press twice to delete all
old messages when the
telephone is not in use.
Ì
Press to make or answer a call
/ SPEAKER
using the speakerphone.
Ì
1 Press and hold to set or dial
your voicemail number.
Ì
Press to switch to tone dialing
temporarily during a call if you
have pulse service.
Ì
While entering names, press
to change the next letter to
upper or lower case.
Ì
# Press and hold to enter the
QUIET/
QUIET mode setting screen,
or to deactivate QUIET mode.

Basic initial settings

We recommend you program your telephone system
before use. The following are a few examples of common
features to set before using the telephone. Refer to the
Handset settings, Telephone base settings and Answering
system settings in the Abridged user's manual or the online
Complete user's manual for detailed instructions on setting
all telephone features.
Date and time
Note: Set the date/time before using the answering system.
Using a cordless handset or the telephone base:
1. -> CID or DIR -> Set date/time -> SELECT.
2. Enter the month, day and year using the dialing keys ->
SELECT.
3. Enter the hour and minute using the dialing keys.
4. CID or DIR to choose AM or PM -> SELECT.
Basic answering system setup via
voice guide
You can follow the voice guide to record your own
announcement, set the number of rings and set the
message alert tone.
Using the telephone base:
CID or DIR -> Answering sys -> SELECT.
1. ->
CID or DIR -> Voice guide -> SELECT.
2.
3. Set up the answering system by inputting the
designated numbers, as instructed.