Subscribe to Our Youtube Channel
Related Manuals for Wassermann HSS-99
Summary of Contents for Wassermann HSS-99
- Page 1 Trimmer HSS-99 and HSS-88 Orthodontic Accessories For Bite Orientated Trimming of Plaster Jaw Models USER MANUAL...
- Page 2 Dear customer, Thank you for choosing a product from the Wassermann range. Wassermann Dental- Maschinen incorporates the highest standards of quality and the latest technology. In order to enjoy maximum performance and years of trouble-free operation, please read this user manual carefully before you connect this device and start work, and operate the device according to the recommended guidelines.
-
Page 3: Table Of Contents
Contents 1 Features............................4 1.1 Orthodontic Model Table.........................4 1.1.1 Figure HSS-99 Model Table KMS according to Begg (Item no. 164130)........4 1.1.2 Figure HSS-88 Model Table KMS according to Begg (Item no. 168140)........4 1.2 Laser Light Guide for Orthodontic Model Table................5 1.2.1 Figure HSS-99 Laser Light Guide for Model Table (Item no. -
Page 4: Features
The angle limit stop (Fig. page 8) is easily pivoted away. • 1.1.1 Figure HSS-99 Model Table KMS according to Begg (Item no. 164130) 1.1.2 Figure HSS-88 Model Table KMS according to Begg (Item no. 168140) -
Page 5: Laser Light Guide For Orthodontic Model Table
Due to the electrical connections, the installation of the guide light is performed by • our Wassermann Service or one of our licensed specialist companies. 1.2.1 Figure HSS-99 Laser Light Guide for Model Table (Item no. 164110) 1.2.2 Figure HSS-88 Laser Light Guide for Model Table (Item no. 168120) -
Page 6: Safety Symbols Used In This Manual
Make sure that the equipment is connected to the correct power source. The user can adjust the laser light guide himself at any time. Due to the electrical connections, the installation of the laser light guide is performed by our Wassermann Service or one of our licensed specialist companies. -
Page 7: Responsibility For Operation Or Damage
The orthodontic accessories has to be maintained and operated in accordance with this user manual. Wassermann Dental-Maschinen GmbH is not responsible for damage arising from the nonobservance of these instructions. Warranty and responsibility provisions contained in the sales and supply conditions of... -
Page 8: Application
The angle limit stop is pivoted away (Fig. 2). Fig. 1 Fig. 2 Only use the accessories for this type of application. The accessories for producing 3D orthodontic models are available for the trimmer HSS-99 and HSS-88. Even subsequent upgrade is possible without any problems. -
Page 9: Before Starting
Before Starting Transport Before transporting the unit/laser light guide, ensure that it has been unplugged from the power socket. Make sure that it is packed correctly in order to avoid accidental damage. Be sure to check for any transport damage when unpacking the goods. Note down any damage if found. -
Page 10: Installation/ Start-Up
Installation/ Start-up For further information please see the manual of your trimmer HSS-99 or HSS-88*. Finally, insert the power plug into the socket, making sure that the mains and the unit operate on the same voltage. Operation General Operating Instructions... -
Page 11: Grinding Process
Grinding Process 8.2.1 Important Advice Concerning the Usage of the Orthodontic Model Table Use the right hand to move the model table back and forth with moderate pressure. 8.2.2 Usage of the Orthodontic Accessories The light shines immediatly if the trimmer is switched on by the rotary switch. After you switch the trimmer on, wait a few seconds for the motor to come up to speed. -
Page 12: Adjustment Of The Laser Light Guide
Adjustment of the Laser Light Guide The user can adjust the guide light himself at any time. Remove the 2 recessed head screws (A). Remove the cover plate (B). Remove the key for the adjustment (C, Item no. 164101). ... -
Page 13: Troubleshooting
Troubleshooting Fault Cause Solution No free movement of Dirt Please see the slider or the 9.1.1 Cleaning instructions for the model table angular adjustment No laserlight Note for service technicians: Please check the power supply voltage (approx. 11.8 V at idle speed). Power supply If the power supply voltage at idle speed deviates defective... -
Page 14: Cleaning Instructions For The Orthodontic Model Table
Cleaning Instructions for the Orthodontic Model Table 10.1.1 If the free movement of the slide or the angular adjustment is not working properly, • please clean the Orthodontic Model Table. Use water and a clean cloth only! • Do not use any kind of grease or oils to lubricate the moving parts! •... -
Page 15: Maintenance
10.2 Maintenance The orthodontic accessories do not require any servicing. Just make sure that thea are kept clean (Please see 9.1). 10.3 Repairs Servicing or repairs to the unit/orthodontic accessories has only to be carried out by qualified technicians. Only original spare parts are to be used. Responsibility for the product is voided if unauthorised persons alter it or if inappropriate components are installed. -
Page 16: Scope Of Delivery/ Accessories
10.8 Scope of Delivery/ Accessories Included parts Item no. HSS-99 Orthodontic Model Table KMS according to Begg 164130 HSS-88 Orthodontic Model Table KMS according to Begg 168140 Laser Light Guide for Orthodontic Model Table HSS-99 164110 Laser Light Guide for Orthodontic Model Table HSS-88... -
Page 17: Technical Data
Technical Data Laser Light Guide for Orthodontic Model Table HSS-99 – Item no. 164110 Laser Light Guide for Orthodontic Model Table HSS-88 – Item no. 168120* Dimensions (W x H x D) 46 x 311 x 175 mm HSS-99 without power pack... -
Page 18: Eu Declaration Of Conformity
Directional Lamp Dental-Maschinen GmbH for dental Rudorffweg 15-17 applications 21031 Hamburg Germany Model: Directional lamp laser cpl. HSS-99 Item no. 164110 Directional lamp laser cpl. HSS-88 Item no. 168120 Applicable DIN EN 61010-1 standards: DIN EN 61000-6-3 DIN EN 61000-6-1... - Page 19 Notes:...
Need help?
Do you have a question about the HSS-99 and is the answer not in the manual?
Questions and answers