Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AUDAC NOBA8A
Summary of Contents for AUDAC NOBA8A
- Page 1 NOBA8A User Manual www.audac.eu...
- Page 2 However, updates on the specifications, functionality or software may have occurred since publication. To obtain the latest instruction manual or obtain additional product information, please visit the product page on www.audac.eu. For information about software version updates, please visit www.audac.eu/software.
-
Page 3: Table Of Contents
Control panel description Connection panel overview Connection panel description RMT40 remote control overview RMT40 remote control connection Chapter 3: Connecting the NOBA8A Chapter 4: Loading presets & firmware updates hapter 5: Mounting the NOBA8A hapter 6: Additional information Technical specifications... -
Page 5: Introduction
The perfect acoustic experience is guaranteed when the entire audio frequency spectrum is equally distributed. The slick look of the NOBA8A allows it to be placed against a wall, on the ceiling or even underneath furniture, yet due to the unique composition of its parts, NOBAA ensures a much better spreading of sound waves than other similar cabinets. -
Page 6: Precautions
Precautions READ FOLLOWING INSTRUCTIONS FOR YOUR OWN SAFETY ALWAYS KEEP THESE INSTRUCTIONS. NEVER THROW THEM AWAY ALWAYS HANDLE THIS UNIT WITH CARE HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS NEVER EXPOSE THIS EQUIPMENT TO RAIN, MOISTURE, ANY DRIPPING OR SPLASHING LIQUID. AND NEVER PLACE AN OBJECT FILLED WITH LIQUID ON TOP OF THIS DEVICE NO NAKED FLAME SOURCES, SUCH AS LIGHTED CANDLES, SHOULD BE PLACED ON THE APPARATUS DO NOT PLACE THIS UNIT IN AN ENCLOSED ENVIRONMENT SUCH AS A BOOKSHELF... -
Page 7: Caution Servicing
CAUTION - SERVICING This product contains no user serviceable parts. Refer all servicing to qualified service personnel. Do not perform any servicing (unless you are qualified to) EC DECLARATION OF CONFORMITY This product conforms to all the essential requirements and further relevant specifications described in following directives: 2014/30/EU (EMC) and 2014/35/EU (LVD) WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) -
Page 9: Chapter 1: Pin Connections And Connectors
Chapter 1 Pin connections and connectors CONNECTION STANDARDS The in- and output connections for AUDAC audio equipment are performed corresponding to international wiring standards for professional audio equipment. 3-Pin Terminal Block: For balanced signal input & link output connections. Left:... -
Page 10: Chapter 2: Front & Rear Panel
Chapter 2 NOBA8A overview The aluminum enclosure features a grill on both sides. One side includes the amplifier, while the bass port is located on the opposite side. To guarantee an optimal heat dissipation and ventilation for the amplifier and to allow air-circulation through the bass port, make sure that both sides remain uncovered when installed. -
Page 11: Connection Panel Overview
Standby mode: A standby mode switches the NOBA8A to energy saving mode when no input signal is detected for a certain period. The standby time is default configured to an interval of 5 minutes and can be adjusted or disabled by software configuration / preset loading. -
Page 12: Rmt40 Remote Control Overview
RMT40 Remote control overview (optional) Enter config mode (Hold 5 seconds) Mute Volume down Volume up Level up (Config mode only) Level down (Config mode only) Previous speaker (Config mode only) Next speaker (Config mode only) Exit config mode (Hold 1 second) Recall default settings (Hold 5 seconds) RMT40 Remote control description... -
Page 13: Chapter 3: Connecting The Noba8A
For more information how specific presets have to be loaded, check chapter 4 of this instruction manual. The following diagrams give an overview of specific setups with a NOBA8A and two of four high/mid frequency loudspeakers. Channel L (2) -
Page 14: Chapter 4: Loading Presets & Firmware Updates
The files can be downloaded from the set solution page on the audac website (www.audac. eu) and must be copied to an USB memory drive for insertion into the NOBA8A speaker. Make sure the files are stored inside an ‘AUDAC’ subdirectory and the file extension is ‘*.SOL’. (The file path should be ‘...\AUDAC\FILENAME.SOL’). -
Page 15: Chapter 5 Mounting The Noba8A
Chapter 5 Mounting the NOBA8A The NOBA8A comes standard delivered with a mounting bracket for on-wall installation. The installation of this bracket shall be done according to a simple 5-step procedure as described below: Step 1: Remove the rubber feet The cabinet comes delivered with 4 pcs of rubber feet assembled supporting the cabinet for floorstanding use. - Page 16 Step 3: Mounting the wall plate Mount the wall plate to the installation location of the NOBA8A. The wall plate has to be fixed using four screws. The exact screw positioning is shown in the drawing below. The used fasteners should be chosen depending on the mounting surface (brick, concrete, wood, gypsum, ...
-
Page 17: C Hapter 6: Additional Information
Chapter 6 Additional information Technical specifications Max power subwoofer 200 Watt RMS power subwoofer 100 Watt Sensitivity subwoofer (1W / 1m) 83 dB Sound pressure (Max W / 1m) 105 dB Frequency response ± 3 dB 90 Hz - 350 Hz Frequency range -10 dB 45 Hz - 350 Hz @ 4 Ω... - Page 18 Accessories included Wall mount bracket Optional accessories RMT40 RF remote control - 2.4 GHz MBK410C Ceiling mount bracket...
-
Page 19: Notes
Notes... - Page 20 Notes...
Need help?
Do you have a question about the NOBA8A and is the answer not in the manual?
Questions and answers