Advertisement
Translation of the Original Operating
GB
Instructions PROXXON GG 12 Set
Dear Customer,
Please read these safety regulations and operating
instructions before using the tool.
WARNING!
Read all safety warnings and instructions. Failure to
follow all safety warnings and instructions listed
below may result in electric shock, fire and/or
serious injury.
KEEP ALL SAFETY WARNINGS AND INSTRUCTIONS FOR
THE FUTURE!
Safety information:
General safety regulations:
IMPORTANT
1. Keep the working area tidy.
2. Check the tool for damage before each use (connection
lead, safety devices, etc.); have defective components
replaced by a specialist.
3. This tool meets the relevant safety regulations. Repairs
(e.g. replacing the mains lead) may only be carried out
by an electrician.
4. Never work without the safety devices provided.
5. Do not use electric tools in the rain, in damp
environments or near inflammable liquids or gases.
6. Only use tool if the handle is dry and free of grease.
7. Avoid body contact with earthed objects, e.g. pipes,
radiators, ovens and refrigerators.
8. Protect connection lead from heat and sharp edges and
route so that it cannot be damaged.
9. Do not use lead to pull the plug out of the voltage
supply.
10. Do not lift the tool by the lead.
11. Keep children and people not involved away from the
working area.
12. Store tools out of the reach of children when not in use.
13. Do not overload your tool.
14. Do not use the tool for operations for which it was not
intended.
15. Replace blunt tools promptly.
16. Check inserting tools prior to every start-up by visually
inspecting their completeness and suitability for the
application.
17. Fasten or clamp the work piece securely.
18. Clean the tool thoroughly after use (disconnect plug).
19. Remove the mains plug from the socket when not in use
or prior to maintenance, tool change or repair.
20. Only insert plug if the tool is switched off.
21. Wear protective goggles (in case tool breaks).
22. If necessary, wear dust mask.
23. Only wear suitable work clothes (no baggy sleeves, ties,
jewellery).
24. Wear hair protector if you have long hair.
25. Only use accessories and spare parts recommended by
PROXXON.
- 4 -
26. If necessary, use a dust extraction system (but only use
suitable dust extractor, risk of fire from sparks).
27. Do not use the tool if you are not concentrated or under
the influence of alcohol.
28. Keep fingers away from rotating and fast-moving tools.
29. Always keep operating instructions in a safe place close
at hand.
Please also read the following carefully:
PROXXON does not accept liability for damage that occurs if:
1. the tool is handled in a manner which constitutes
improper use
2. it is used for purposes which are not specified in the
instruction manual
3. the safety regulations are not observed
Warranty claims are invalid if:
1. the tool is operated incorrectly
2. the tool is used improperly
3. modifications or interventions are made on the tool
– Do not leave the tool switched on.
– Only allow children to operate it under the supervision of
adults.
– Wear protective goggles.
– Secure small work pieces so that they are secure and
stable.
– Keep the working area tidy.
– Do not overload the tool.
– Store tools safely.
Description of the machine
Engraving glass, acrylic and ceramic (and also steel) is an
enjoyable hobby. Congratulations on purchasing the appro-
priate tool for this hobby. This is a precision tool that will
make this pastime a particular pleasure. You will be satisfied
with the result of your work after just a little practice.
Scope of delivery
1 engraving tool GG 12
1 voltage supply unit, model SNG
1 ball-shaped abrasive diamond pencil 1.0 mm
1 ball-shaped abrasive diamond pencil 1.8 mm
1 conical silicon-carbide abrasive pencil
1 bullet-shaped silicon-carbide abrasive pencil
1 piece of glass for experimenting
1 robust case
Only operate the GG 12 with the voltage supply unit provi-
ded or other PROXXON voltage supply units (NG 2/S/E or
NG 5/E).
Note:
Advertisement
