1. Manuals
  2. Brands
  3. Schacht Manuals
  4. Other
  5. WOLF FL3051
  6. Assembly instructions manual

Schacht FL3051 Assembly Instructions Manual

Wolf stroller for installation on schacht wolf pup; schacht wolf pup lt; schacht baby wolf; schacht mighty wolf looms
Hide thumbs Also See for FL3051:
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

WOLF STROLLER
A
folded—ready to travel
F
or InstAllAtIon on
b
W
Aby
olF
Find out more at schachtspindle.com
Schacht Spindle Company 6101 Ben Place Boulder, CO 80301
p. 303.442.3212 f. 303.447.9273
© 2018 Schacht Spindle Company, Inc.
ssembly
W
,
m
And
Ighty
I
nstructIons
open—ready to weave
P
, W
olF
uP
W
l
olF
ooms
FL3051
P
lt,
olF
uP
03.18

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FL3051 and is the answer not in the manual?

Questions and answers

Related Manuals for Schacht FL3051

Summary of Contents for Schacht FL3051

  • Page 1 WOLF STROLLER FL3051 ssembly nstructIons folded—ready to travel open—ready to weave or InstAllAtIon on Ighty ooms Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212 f. 303.447.9273 © 2018 Schacht Spindle Company, Inc. 03.18...
  • Page 2 The Wolf Pup 8.10 loom has its own Wolf Pup 8.10 Stroller (FL3052), with a different instruction booklet. If you received this booklet with your Wolf Pup 8.10 Stroller, please call or visit the Schacht website for the correct booklet. rear brace...
  • Page 3 BABY WOLF AND MIGHTY WOLF LOOMS ssembly nstructIons Install the Wolf Stroller on a hard sur- face. Open the loom to weaving position (see front cover illustration). When you are working on the front caster blocks, set the treadle bar on a block of wood or a couple of books to raise the front of the loom about two inches.
  • Page 4 into the loom leg using a rubber mallet or hammer and a piece of scrap wood. Place a washer and a lock nut on the carriage bolt and tighten the lock nut enough to draw the head of the carriage bolt into the wood of the leg (Figure 4).
  • Page 5 WOLF PUP / WOLF PUP LT LOOMS ssembly nstructIons NOTE: If you installed wheels on your Wolf Pup loom, we recommend that you take them off before installing your Wolf Stroller. Install the Wolf Stroller on a hard surface. Open the loom to weaving position (see front cover illustration).
  • Page 6 Drill upper hole to secure rear caster black plastic 2" machine spacer blocks. Assemble the black plastic spacer screw onto the 2-½" hex bolt. Slide the bolt through hole (G) from the inside of the loom, and tighten a wing nut down on the exposed bolt (Figure 9).
  • Page 7 Attach the bolt to hold the front of the metal support bar when the loom is folded (Figure 12). From the inside of the loom, " hex bolt insert a 1-¾" hex bolt through the hole (G) in the front caster block. Secure the hex bolt with a washer and a lock nut.
  • Page 8 DRILLING GUIDE TEMPLATE Use a ¼" drill bit. For Baby Wolf looms with serial numbers lower than 4-1608, 4-4-1609, and 8-546, you will need to drill holes in the inside and outside legs using this template. Photocopy this page so that you can use a fresh template for each leg.

Table of Contents