Schacht MIGHTY WOLF LOOM Series Assembly Instructions

Advertisement

Quick Links

MIGHTY WOLF LOOM
A
ssembly
PARTS
Wrapped onto warp beam:
3X apron bars
2X lease sticks (with holes)
2X additional 37" dowels (cherry looms
only)
Accessory pack:
1X brass reed hook
1X warp beam crank handle
14X 29" apron cords (or 2X 30-foot apron
cords for cherry looms only)

BEFORE YOU BEGIN

■ All Wolf looms assemble in a similar way. Watch the Baby Wolf assembly video on our
Youtube channel (www.youtube.com/user/schachtspindle).
■ You'll find a complete labelled diagram of the Wolf loom in your Maintenance and
Warranty manual and at schachtspindle.com.
■ Wolf loom legs are called out by where they cross each other. The legs that touch the
ground at the front of the loom are called "inside" legs because they are covered by the
"outside" legs when they cross at the loom center.
■ The beater is at the front of the loom. The brake is on the right side of loom.

UNFOLDING THE LOOM

Remove all plastic wrap from the loom.
1.
Remove both shipping braces by slightly
loosening the back beam knobs and
front beam screws holding them in place.
Discard the braces and tighten the knobs
and screws.
Slightly loosen the black fold knobs
2.
on each side of the loom (Figure 1).
Generally, a single turn will do.
Loosening the knobs all the way or
removing them can cause the loom to
collapse, which could result in injury.
Stand at the side of the loom. Hold the
3.
front and rear beams together slightly. Pull
the slide lock bars out toward the back of
the loom.
Find out more at schachtspindle.com
Schacht Spindle Company 6101 Ben Place Boulder, CO 80301
p. 303.442.3212 f. 303.447.9273
© 2018 Schacht Spindle Company, Inc.
I
nstructIons
TM
1X 3/8" cap nut for warp beam crank
handle
1X 3/8" washer for warp beam crank
handle
3X extra 8/32" hex nuts for shafts
Maintenance and Warranty Manual
4-shaft looms:
800X heddles
24X
tie-up cords
8-shaft and 4 Now-4 Later looms:
1000X heddles
80X
tie-up cords
Continue holding onto the front and
4.
rear beams and allow the loom to unfold
all the way. If there is a warp on the loom,
you may need to hold down the brake
release pedal with your foot to loosen the
warp as you unfold the loom.
back beam
knob
slide lock bar
slot in
castle
FIGURE 1: UNFOLDING THE LOOM
FL3002
FL3014
FL3004
FL3022
FL3012
FL3024
shipping brace
front beam
screw
fold knob
FRONT OF
LOOM
12.18

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MIGHTY WOLF LOOM Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Schacht MIGHTY WOLF LOOM Series

  • Page 1 LOOM the loom. FIGURE 1: UNFOLDING THE LOOM Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212 f. 303.447.9273 © 2018 Schacht Spindle Company, Inc. 12.18...
  • Page 2 When the loom has completely opened, push the fold knobs down to the bottom of the slots in the castle. Tighten the knobs. You can push in the slide lock bars to get them out of the way. 3/8" washer FOLDING THE LOOM To prevent treadles from dragging on cap nut...
  • Page 3 pinched cord through the second hole in one of the slots in the shaft frame. Using the cord. Pull on the pinched cord until very gentle pressure, flex the heddle a new loop forms that is large enough bar just enough to fit the other end into for the apron bar to slip through (Figure the slot on the opposing side of the shaft 3C).
  • Page 4 After you have completed your tie-up, check each treadle by pushing it all the way to the floor and releasing it, making sure that the button of each tie-up cord is up against the treadle and that each cord hangs straight down to the treadle. There is a 1/2"...

This manual is also suitable for:

Mighty wolf loom fl3002Mighty wolf loom fl3004Mighty wolf loom fl3012Mighty wolf loom fl3014Mighty wolf loom fl3022Mighty wolf loom fl3024 ... Show all

Table of Contents