Table of Contents
Advertisement
Quick Links
Installation & Operations Manual
• 2100-TDL Landline Dusk2Dawn Tower
• 2100-TDC Cellular Dusk2Dawn Tower
• 2100-TD9 900 MHz Dusk2Dawn Tower
• 2100-TDT 2-Way Radio Dusk2Dawn Tower
• 2100-TDV VoIP Dusk2Dawn Tower
• 2100-TDW Wi-Fi VoIP Dusk2Dawn Tower
Made in the USA
2 Year Warranty
Emergency Tower Phone
N56W24720 N. Corporate Circle
866-850-8854
Sussex, WI 53089
www.rathcommunications.com
RP8500050
Ver. 7
10/18
Advertisement
Table of Contents
Related Manuals for Rath 2100-TDL
Summary of Contents for Rath 2100-TDL
- Page 1 Installation & Operations Manual Emergency Tower Phone • 2100-TDL Landline Dusk2Dawn Tower • 2100-TDC Cellular Dusk2Dawn Tower • 2100-TD9 900 MHz Dusk2Dawn Tower • 2100-TDT 2-Way Radio Dusk2Dawn Tower • 2100-TDV VoIP Dusk2Dawn Tower • 2100-TDW Wi-Fi VoIP Dusk2Dawn Tower N56W24720 N.
-
Page 2: Table Of Contents
Thank you for purchasing RATH’s Emergency Tower Phone. We are the largest Emergency Phone Manufacturer in North America and have been in business for over 35 years. We take great pride in our products, service, and support. Our Emergency Phones are of the highest quality. -
Page 3: Description
Description Figure 1: Front & Back View Features: • ADA compliant (hands free operation) • LED call status indicator Panel 1 • Powder coated steel construction inside and out • Aluminum access panels powder coated inside and out • Weather and vandal resistant •... -
Page 4: Items Needed
Items Needed for Installation • Concrete for 16” deep, 2’ diameter slab • 1/4” spanner adapter (provided to remove • Rath Kit 7476* or 7477** Access Panel 1) • #1 Phillips screwdriver • Adjustable wrench • 1/4” driver • Analog phone line (if using 900 MHz or a Landline) •... -
Page 5: Communication
5. Verify SmartPhone is plugged into the FXS port on Cellular Module. Note: If the Sim card is not provided to Rath at time of purchase, an active Sim Card will need to be installed into Sim Card slot. CDMA Cellular: 1. -
Page 6: Phone Programming
VoIP & Wi-Fi VoIP: See additional manual. Programming the Phone 1. You can program the phone on-site or remotely. Note: Cellular and 900 MHz applications cannot be remotely programmed. 2. If programming on-site, remove the face plate. Use the #10 spanner bit provided to remove the 6 security screws. -
Page 7: Phone Testing
If you have answered YES to all questions, you have successfully installed and tested the phone. If you answer NO to any question, proceed to the Troubleshooting Section. * Rath recommends the tower phone be tested on a regular basis to ensure proper operation. Adjusting the Volume If the volume is too low or high, adjust it by referring to the diagram and instructions below. -
Page 8: Troubleshooting
Troubleshooting Possible Cause & Solutions Problem No dial tone when the • Check to make sure the phone line is connected to button is pushed: SmartPhone board. • Verify dial tone and voltage on phone line going into unit. Audio is low from the •... -
Page 9: Wiring
Wiring Diagram Wiring Strobe Photocell Strobe Constant Positive 120v Negative Charging/Finishing/Ready Ground Dusk2Dawn Charging Station Transformer (Only if using 277 or 480v power) Reference the manufacturer’s instructions for the wire connections Enter Record Play / Pause Stop Wago Connector to front plate BATTERY Phone line to cellular unit...