Cleaning The Brush Roll; Troubleshooting - RugDoctor FlexClean FCM-1 User Manual

CLEANING THE BRUSH ROLL

2
1
TURN THE
MACHINE OFF
Push the POWER
SWITCH to the
GENTLY LAY THE MACHINE
"OFF" position
DOWN ON ITS SIDE
and unplug the
machine from the
Remove CLEAN WATER TANK and
grounded outlet.
DIRTY WATER TANK. Gently position
the machine on its side to access the
BRUSH ROLL.
HOW TO CHANGE THE BRUSH ROLL
2
1
TURN THE REMOVE THE TANKS
MACHINE
Remove
OFF
the CLEAN
WATER
Push the
TANK and
POWER SWITCH to
DIRTY
the "OFF" position
WATER
and unplug the
TANK and
machine from the
set aside.
grounded outlet.
4 5
UNLOCK THE BRUSH
ROLL LOCK
Turn the BRUSH ROLL LOCK to
the UNLOCK positon using coin or
screwdriver.
REMOVE BRUSH ROLL
LOCK COVER
Brush Roll
Lock
8
7
REPLACE BRUSH ROLL MOVE MACHINE
LOCK COVER INTO UPRIGHT
POSITION
Turn the BRUSH ROLL LOCK to
the LOCK position using a coin
Replace DIRTY
or screwdriver.
WATER TANK and
CLEAN WATER
TANK.
Brush Roll
Lock
18
F L E X C L E A N® A L L - I N - O N E F L O O R C L E A N E R
3
REMOVE ANY DEBRIS FROM
BRUSH ROLL
3
LAY THE MACHINE ON ITS SIDE
Gently lay the machine
down on its side.
6
Old Brush Roll New Brush Roll
REPLACE THE BRUSH ROLL
Remove old BRUSH ROLL and
replace with NEW BRUSH ROLL.
9
Now You Are
Ready To Clean
| U s e r M a n u a l

TROUBLESHOOTING

The following Troubleshooting Guide is provided to help you resolve issues that
may arise with common usage of the machine.
PROBLEM POSSIBLE REASON
›
Power Cord not plugged in
›
Power Button not turned on
NO POWER
›
Not pressing Cleaning Solution
Trigger
›
Clean Water Tank is empty or low
NO / LOW SPRAY,
›
Clean Water Tank is not locked or
MACHINE
installed correctly
›
Valve of Clean Water Tank is clogged
›
Upholstery Tool Connection is not
NO / LOW SPRAY, installed properly
UPHOLSTERY
TOOL
›
Dirty Water Tank Is full
›
Dirty Water Tank is not installed
NO / LOW
correctly
SUCTION,
›
Nozzle is not properly installed
MACHINE
›
Upholstery Tool Connection is not
NO / LOW
installed properly
SUCTION,
›
UPHOLSTERY
Kink or obstruction in Vacuum Hose
TOOL
›
If something is lodged in the Brush
Roll, brush will stop rotating
ROTATING BRUSH
DOESN'T ROTATE
If you are not able to resolve or have other questions call the customer service
hotline at 1-800-784-3628.
r u g d o c t o r . c o m | 1 - 8 0 0 - 7 8 4 - 3 6 2 8
HOW TO FIX
›
Plug Power Cord into wall outlet.
›
Press Power Button to "Floor Clean or
Upholstery" position.
›
Press and hold Cleaning Solution Trigger.
›
Fill Clean Water Tank with water and solution.
›
Lift up Clean Water Tank, and place back into
position. Tank should click into place when
positioned properly.
›
Remove valve from bottom of Clean Water Tank.
Clean with warm soapy water.
›
Disconnect plastic Upholstery Tool Connector
at end of the Upholstery Hose by pinching the
sides and pulling away from the base. Reconnect
Upholstery Tool Connector. You will feel the tool
lock into place.
›
Empty Dirty Water Tank and replace empty tank
when finished.
›
Lift up Dirty Water Tank and place back into
position.
›
Disconnect Nozzle. Reconnect Nozzle ensuring
the tabs are latched at the bottom and the latch
is fully engaged.
›
Make sure the Upholstery Tool Connection
is fully inserted into the Upholstery Tool port.
›
Unkink or remove obstruction in Vacuum Hose.
›
Turn machine off and unplug Power Cord from
outlet. Check that there is nothing stopping the
Brush Roll from rotating. The Brush Roll can be
removed by unlocking the cover with a coin or
screwdriver on the bottom of the machine.
Clean and check the Brush Roll spins freely.
Replace the Brush Roll and secure by locking
the Brush Roll cover. Then plug in the Machine
and turn the Machine on to continue cleaning.
19