Advertisement
Quick Links
IAG Performance Transfer Gears Installation
Part# IAG-DRV-1000, IAG-DRV-1010
Tools Required: 12mm Wrench, 3/8" Torque Wrench,
14mm Wrench, 3/8" ratchet, 12mm Socket, 14mm
Socket, 17mm Socket, 3/8" x 8" extension, Roll Pin
Punches, Press, Bearing Puller, Snap Ring Pliers, Needle
Nose Pliers, U-Joint Press, Hammer
Thank you for choosing IAG Performance. Please follow
the instructions below for an easy installation.
1. Start by draining the transmission fluid.
2. Next remove the (4) 12mm nuts and bolts holding the
driveshaft to the rear diff using a 12mm wrench. Then
remove the driveshaft from the vehicle.
IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com
1
Advertisement
Related Manuals for IAG IAG-DRV-1000
Summary of Contents for IAG IAG-DRV-1000
- Page 1 2. Next remove the (4) 12mm nuts and bolts holding the driveshaft to the rear diff using a 12mm wrench. Then remove the driveshaft from the vehicle. IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...
- Page 2 3. Next remove the down pipe from the vehicle. Then remove the transmission cross member. IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...
- Page 3 5. Remove the shift linkage, shift rod support and mount from transmission. Then remove the shifter knuckle from the transmission using a roll pin punch. Mark the top of knuckle to insure proper re-installation. IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...
- Page 4 Make sure to unplug the electrical connector on diff before removing! There are 4 clam shell bearing that will come out with the diff. IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...
- Page 5 7. Remove the bearings from the output shaft using a press or bearing puller. IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...
- Page 6 Spin the bearing while pressing it onto shaft making sure the bearing doesn’t bind or get damaged during install. IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...
- Page 7 48nm (35.4ft lbs). Make sure the shaft is not loose and spins smoothly, if it is loose or too tight it will require shimming. IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...
- Page 8 Next press the bearing onto the new drive gear and re-install the snap ring. There are shims on the drive gear, these will be re-used so do not lose them! IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...
- Page 9 IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...
- Page 10 Torque the housing bolts to 48nm (35.4ft lbs). Then re-install shifter linkage and transmission cross member. IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...
- Page 11 IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...
- Page 12 After the new yoke is installed make sure it freely moves in all directions. If it is tight you can tap on the yoke to free up the U-Joint. IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...
- Page 13 IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...
- Page 14 15. Re-install the drive shaft, refill the transmission fluid, and re-install down pipe bracket and down pipe. IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com...