Advertisement
zz
is the position of the first digit of the balance in the
reply SMS from the provider
After this sequence has been sent once, the car alarm will check the
balance automatically every xx days and if the balance is lower than yyy
the user will be notified (TEL1)
If the CREDIT instruction is enabled in the above way, the user can also
obtain the current balance by the instruction CREDIT
To disable the automatic balance checking set the time period "xx" to 00.
13.7. Roaming
If you travel abroad and your SIM card supports roaming, the car
alarm will work there too.
13.8. Reset GSM
If you need to disconnect and then reconnect the GSM module to the
GSM network, then use the command "MASTER RESET GSM".
This does not affect any settings and is typically used for GPRS
activation or charging up credit. This command always requires the
Master code.
13.9. Service instruction
The DINFO instruction allows you to obtain current settings,
information about the quality of the GSM signal, the registration code
for GSMLink devices and some other parameters. This command
always requires the Master code.
Example of instruction: MASTER DINFO
Example of response: Car alarm reports: CA-1803A, SN:123456,
SV:01, LV:03, RK:ABCDE-12345-FG67, R:01, GSM:25,GPS:5,
Time:3.2.06 11:35
CA-1803A
SN:123456
SV:01
LV:03
RK: ABCDE-12345-FG67
R:01
GSM:25
instant quality of GSM signal (ranging from 0 to 32 (best))
GPS:5
14. AUX output
AUX output can be set to one of the following modes.
External sensor power supply – if set to this mode, the output
switches to +12V when the car alarm is armed. Current limit is 30mA.
AUX bus – this mode allows you to connect up to four CR-11A modules
to the bus. This enables you to extend car alarm functionality via the power
output. There are two outputs available: A and B. They can be operated by
pressing two buttons together on the key fob RC-8x (see instructions to
CR-11A), or using SMS instructions. This allows you to operate
independent heating, refrigerators, flashing lights etc.). The car must not be
immobilized by use of this module, because the output reacts to incoming
SMS instructions in every state of the car alarm, in particular, while the car
is on the run, thus possibly not under the user's control which would put
persons in the vicinity of the car into danger.
Instruction
AUXA (B)
AUXA ON (OFF)
AUXB ON (OFF)
AUXA xxM in xxxS
AUXB xxM in xxxS
Example of an instruction to switch B relay on for 30 seconds:
AUXB 30S
* Maximum switch-on time is 60 minutes.
* If a relay (A or B) is switched on while arming the car, it will be
switched off. In addition, the A relay, when switched on, will also be
switched off while disarming the car.
15. The back-up battery and voltage monitoring
To handle an absence of supply voltage in the car (disconnecting the
main battery, deliberate damage etc.) the car alarm is equipped with a
BB-02 backup battery. The battery supplies the car alarm when no
supply voltage is present (for 5 hours minimum). Except for the
acoustic siren, the BB-02 backs-up all the functions of the car alarm.
The car alarm is supplied with a small current from the BB-02. Fully
charging a fully discharged battery requires 5 days. In the case of a
supply voltage outage, the BB-02 starts to generate a voltage either for
the outage duration or until it is completely discharged. While testing it
or being handled, it is possible to protect the backup battery from being
completely discharged by briefly shorting the BB-02's terminals (the
BB-02 has to be disconnected from the power supply). This causes
disconnection of the electronics inside the back-up battery. In the case
of switch-over to BB-02 operation (after a voltage drop under 8.5V or
after complete disconnection of the battery), an SMS will be sent with
GSM car alarm CA-1803BT „Athos"
car alarm version
identification number of the product
software version
language version
registration code for GSMLink
current Reset mode of the device
number of visible satelites (0-16)
Status
Relay switches on for 1 second
ON - Switch on permanently*
OFF – Switch off permanently*
xxM – numeric value of requested
duration
of
the
relay
to
switched on, in minutes
xxxS – as above, in seconds
information about backup battery operation. An SMS will also be sent
after the recovery of the main power supply voltage (at least 10
minutes).
16. Emergency RESET
In the case of an emergency, when no installation MASTER code is
available, it is possible to perform an emergency RESET of the car alarm
even without the code. Such a reset causes the car alarm to be set to
factory defaults, including access codes (stated in the manual). Caution:
all pre-programmed numbers, Locator parameters, DIP and SET
parameters will be deleted. You perform an emergency reset as follows:
Turn the power supply (including back-up battery, if any) off. Pull the SIM
card out of the car alarm and insert it into a phone, enter "RESET" as a
name into the SIM card's phone directory, and enter "0" for the
corresponding phone number. Insert the SIM card back into the car
alarm and turn the power supply on. The reset is indicated by 4 beeps.
Please contact us by phoning +420 483 559 987 or +420 606 652
997. You can also e-mail us your suggestions to improve our services
and products to auto@jablotron.cz.
17. Specification
Power supply
Stand-by consumption
Max. consumption (during GSM communication)
GSM band
Transmitted power
Vf frequency
Operational temperature
Output SIR
Immobilization
Central locking outputs
Complies with
Can be operated according to ERC/DEC98(20,21), ERC REC 70-03
Safety
EMC
Radio interference
JABLOTRON ALARMS a.s. hereby declares that the CA-1803BT is in
compliance with the essential requirements and other relevant provisions
1999/5/EC
of Directive
assessment can be found at www.jablotron.com, Technical Support
section
Note: Although this product does not contain any harmful materials we
suggest you return the product to the dealer or directly to the producer after
use.
be
6/6
12/24V DC (8-32V)
E-GSM / GPRS 900/1800MHz
2 W for GSM900, 1 W for GSM1800
+12V (24V), max. load 1.3A
8A permanently, 12A intermittently
max. 200mA, to GND
pulses 0.5s, 4s or 60s (optional)
ECE Regulation No. 97.00
EN 55022, EN 50130-4
ETSI EN 301 419-1, EN 301 511, ETSI EN 300 220
ETSI EN 300 328
E
97 RAI-01 4532
8
and
1995/56/EC
The original of the conformity
max. 20 mA
1 A
868.5MHz
-20°C to +70°C
EN 60950-1
MHF56603
Advertisement
