Advertisement
17
SET
18
AUXA
19
AUXB
20
GPS
21
TIME
25
ON
26
OFF
Events:
30
Alarm
31
Alarm cancelled by a user
32
Fire alarm
33
Tamper alarm
34
Disarming
35
Arming
36
Low battery voltage
37
Engine is blocked
38
Engine is unblocked
Source:
40
Ignition key
41
Door contact
42
INP1 activation
43
INP2 activation
44
Low battery voltage sensor
45
Telephone 1
46
Telephone 2
47
Telephone 3
Use only ASCII character set during the text edition.
10. Functions related to GPS
An integrated GPS (Global Position System) allows the car alarm to
provide information about car location with a high precision. The
location can be obtained upon an SMS request or via the GSMLink
internet web page. A service for regularly sent location information is
also available. The car alarm is capable of recording all the car's
locations into internal memory while the car is being used (optional).
Records can be used for statistics about car use (route listing etc.).
The information is also partially available via the GSMLink internet
page. Fully-fledged use is possible using a special service only. In that
case, a central monitoring station is required with information being
automatically
downloaded.
manufacturer or visit the
http://www.jablotron.com
10.1. Location detection using GPS
Using a GPS instruction, you can instantly detect the car's location.
The car alarm responds with the coordinates of the latest known
location. If the current location is not available at the time of reception
of the instruction, or if the car alarm does not change it global position
for a while, the latest location stored in internal memory is sent.
Therefore, messages are supplemented with GMT (Greenwich Mean
Time). The value corresponds to the time of detection related to the
prime meridian. In addition, information about altitude, velocity and
local time of the GSM network is provided. Information about location
can be sent automatically after an alarm has been triggered (see the
DIP switches description).
An example of an instruction sent from an authorized phone: GPS
An example of response: Car alarm reports: Location:
(GMT:3.12.10:35) 50*43.495N;15*11.253E;515;50, Time:3.12.05 11:35
(GMT:3.12.10:35)
50*43.495N;15*11.253E
515
50
Time:3.12.05 11:35
10.2. Time zone setting
To adjust the time information to local time, time zone setting is
possible. The car alarm adds/subtracts the time shift, expressed in
hours, to the GMT time (for middle Europe: +2 hours in summer time,
+1 hour in winter time). This instruction is only available with the
MASTER code.
Instruction: MASTER TIME ±xy
xy is the time shift in hours -3,-2 ...+1,+2 relative to GMT
MASTER TIME GSM
turns on automatic setting via incoming SMS.
10.3. Location change in the armed state
The car alarm allows you to supervise changes in the location of the
car in the armed state. See the corresponding SET parameter.
If switched ON, every change of car location detected during the
armed state triggers an alarm. Because the GPS receiver could be in
stand-by mode (due to energy saving) the car alarm could react with a
delay of up to 10 minutes. This function depends on the accuracy of
GSM car alarm CA-1803BT „Athos"
64
Car alarm reports
65
Status:
66
Armed
67
Disarmed
68
Ignition key ON
69
Ignition key OFF
70
Engine is blocked
71
Engine is unblocked
72
No alarm
73
Alarm timeout
74
Low battery voltage
75
Power failure
76
Power recovery
77
Time
78
Low back-up battery voltage
79
Partially
80
Location
Confirmation SMS:
81
Command accepted
82
Command syntax error
83
New MC code:
84
New UC code:
85
Reset
86
Registered phone number:
87
Credit:
88
LEARN mode, enrolled
For
more
information,
consult
web page.
Greenwich Mean Time (mean meridian)
latitude and longitude
altitude (approximated)
current velocity
current local time
location determination; therefore only use this function as information,
not as a security function.
10.4. Integrated Bluetooth module (BT)
A Bluetooth module is supplied as a built-in part of the CA-1803BT
car alarm. The module allows the car alarm to communicate with
nearby devices equipped with Bluetooth connectivity. For devices like
PDAs, MBAs or mobile phones, such communication can make use of
navigation software running on these devices. When disarmed and
with the ignition key on, the car alarm sends GPS coordinates via the
BT which can be used for navigation. The car alarm authorization code
for device-pairing is 0000. The ignition key must be on during the
pairing process.
If the car stands still for more than 10 minutes, GPS data
transmission may start with a delay of up to 1 minute.
11. Internet remote access
The web site www.GSMLink.cz enables car alarm remote control
(to users) and setting (to installers).
To get internet access to an installed and powered car alarm you will
first be asked to register your car alarm on the first page. You will find
a unique registration code for your car alarm on the warranty card.
12. Central monitoring station communication
The GSM communicator allows central monitoring via GPRS data
protocol. The central monitoring station (CMS) gets arming, disarming and
alarm information. It also regularly checks the communication link to the car
after it is armed. So if anyone tries to tamper with GSM communications, it
will indicate an alarm at the CMS.
13. Additional features
13.1. Car battery low voltage reporting
The built-in voltage drop detector can trigger an alarm if an electrical
device in the car is turned on while the car is armed. The sensor is
active 10 minutes after arming.
13.2. Passive guarding
Via the DIP I parameter it is possible to block the car against starting up
the engine, if the ignition key is turned off for 5 minutes and the alarm is not
set. The function can be turned off by pressing any key on the RC-8x
remote controller. It is also possible to set up the parameter to send a
the
STATUS SMS, which informs the user that the alarm is not set; in the case
that the ignition key is turned off for 60 minutes and the alarm was not set.
13.3. Remote siren activation
You can operate the siren remotely by the SIREN instructions. These
instructions are accepted from all authorized (stored) phone numbers.
Commands are also accepted from any unknown phone number if they
start with the USER code.
Instruction
SIREN ON
SIREN OFF
SIREN
SIREN xxM
or
SIREN xxxS
13.4. Limited number of alarms
If any sensor (input) repeatedly triggers alarms then this particular input
will be bypassed automatically after the third alarm (it will remain bypassed
until the car alarm is disarmed).
13.5. LED indicator signals
LED state
OFF
permanently ON
Regular slow flashing
Regular fast flashing
Interrupted light
Flashing after ignition off
Flashes after ignition on
13.6. Pre-paid SIM card balance
It is recommended not to use prepaid cards in the car alarm. If you
have no other choice than prepaid cards, you can enable the CREDIT
instruction by the following sequence:
MASTER CREDIT uuu..u xx yyy zz
where: uuu...u is the provider's code to obtain the balance
xx
is the time period (in days) for regular checking
yyy
is the threshold level below which the balance is
5/6
Status
activates SIR output permanently
deactivate SIR output
activates SIR output for 30 sec.
xxM – is a numeric value of the
duration of SIR output activation ,
in minutes
xxxS – as above, but in seconds).
Meaning
Disarmed
Connecting to a GSM network or a phone call
Armed
Alarm memory
Car was stopped (immobilization)
GSM network is not available
Number of enrolled remote controls
reported to the user (TEL1)
MHF56603
Advertisement
