Table of Contents
Advertisement
Quick Links
HP34
SL 2.0
Temperature-Luminosity controller
Handbook
MAIN SETTINGS (Run Mode)
DAY SET TEMPERATURE SETTING.
Press DAY TEMP (key lamp flashes):
This messagge will be displayed instead of the
°Set Day temperature.
Press + or - to modify, press DAY TEMP to confirm.
NIGHT SET TEMPERATURE SETTING.
Press NIGHT TEMP (key lamp flashes):
This messagge will be displayed instead of the
°Set Night temperature.
Press + or - to modify, press NIGHT TEMP to confirm.
DAY/NIGHT CONDITION SETTING.
Press LUMIN SET (key lamp flashes):
This messagge will be displayed instead of the
% Set Day/Night condition.
Press + or - to modify, press LUMIN SET to confirm*.
* Down this luminosity Night condition is on: up this luminosity Day condition is on.
Luminosity is represented in 0.0-99.9 ; 0.0 represents total dark, 99.9 represents maximum luminosity.
COSt PROGRAMMING (System constants)
These settings refer to the mode operation of the system and must be made on initial start-up:
press - / + together for at least one second: the message C.O.S.t. will be displayed.
Press than repeatly LUMIN SET until interested variable's message is displayed (see table
below) : variable value and related message will be displayed.
Press + or - to set a new value and then LUMIN SET to confirm.
The next system constant will then appear.
You can press LUMIN SET for a least two second to escape and return to the Run Mode .
M
e
s
. s
V
a
u l
e
d
F i
t .
. 0
° 2
°
C
e t
m
p
e
a r
u t
e r
d
f i
e f
d
F i
L .
1
0 .
°
C
L
u
m
n i
o
i s
y t
d
f i
e f
e r
t
d .
u
r
' 0
D
a
- y
N
g i
h
t t
a r
n
s
t i
o i
n
=
1
t
E
n
P
T
e
m
p
e
a r
u t
e r
e r
p
e r
s
e
A
d
t .
E
. 0
° 0
°
C
n I
p
t u
e t
m
p
e
a r
u t
e r
0
0 .
A
d
L .
u
°
C
n I
p
t u
u l
m
n i
o
i s
y t
s
e
*1) For more details see Operating Diagrams.
*2) tEnP =1 : °C Temperature range.
tEnP =2 : °F Temperature range.
*3) Sensor reading can be adjusted by pressing the + or - keys
M
e
a
n
n i
g
e r
n
i t
l a
n
i t
l a
d
e
a l
y
(
m
n i
u
e t
) s
t n
t a
o i
n
= (
1
°
C
,
=
2
°
) F
c
r o
e r
t c
o i
n
+ (
r o
) -
n
s
r o
c
r o
e r
t c
o i
n
+ (
o
) -
This processor comes already with a preset variable settings.
To reset it to these settings, switch processor off then press LUMIN SET key and keep it pressed
giving power on: release LUMIN SET key when on the screen appear boot message.
d.SEt =25.0° n.SEt =20.0° L.SEt = 30.0
The COSt values are shown in COSt paragraphs.
In some start-up conditions may be useful to work in "hand" mode.
Power off theprocessor, press + key and keep it pressed giving power on:
HAnd message will be displayed (release now + key).
Push + until is displayed number required to be handed (see table relays "N° Relay") and push
LUMIN SET for activing relay.
Pushing again + for increase relay number previous relay is disactivated.
You can press LUMIN SET for a least two seconds to escape and return to the Run Mode
The lights situated at the bottom of the display show the state of the various relays as set out below.
Lamp.
HEAT
COOL
DAY
NIGHT
diF.t
H E A T
DAY
DAY
1/2 diFF
d.SEt
INSTALLATION
How to connect the line
Connect line on terminals L-N; protect supply with adeguate
fuse.
How to connect the sensors
Connect the sensors provided as shown in the diagram. For
remote connections use a standard 0.5-square millimeter
N
o
e t
two-pole wire , taking great care over the connections, by
1 *
insulating and sealing the joins carefully. -O.C.- is displayed
1 *
when the temperature sensor wiring is open,
1 *
displayed when the temperature sensor wiring is short circuit.
2 *
How to connect the contacts
3 *
Output contacts are N.O. (Normally Opened free of voltage)
3 *
on wich is apliable a 4AMP AC1 maximum load.
As it company policy to continually improve the products the Manufacturers
reserve the right to make any modifications thereto without prior notice.
They cannot be held liable for any damage due to malfunction.
State
Heat On
Cool On
Day condition On
Night condition On
diF.t
H E A T
NIGHT
NIGHT
1/2 diFF
1/2 diFF
1/2 diFF
COOL
COOL
DAY
NIGHT
n.SEt
TEMP.
TEMP.
HP34
-S.C.-
is
N° Relay
Contact
1
3-4
1
4-5
diF.L
NIGHT
CONDITION
DAY/
NIGHT
CONDITION
1/2 diFF
1/2 diFF
DAY
CONDITION
L.SEt
LUMIN.
Advertisement
Table of Contents
Related Manuals for POLA HP34
Summary of Contents for POLA HP34
- Page 1 PRESET PROGRAMS HP34 This processor comes already with a preset variable settings. To reset it to these settings, switch processor off then press LUMIN SET key and keep it pressed giving power on: release LUMIN SET key when on the screen appear boot message.
- Page 2 INSTALLATION How to connect the line Connect line on terminals L-N; protect supply with adeguate fuse. HP34 How to connect the sensors Connect the sensors provided as shown in the diagram. For remote connections use a standard 0.5-square millimeter two-pole wire , taking great care over the connections, by insulating and sealing the joins carefully.
Need help?
Do you have a question about the HP34 and is the answer not in the manual?
Questions and answers