Listening Through A Receiver (Home Theater); Check Points Before Requesting Service - Samsung PL-42C71HP Owner's Instructions Manual

Listening through a Receiver (Home theater)

You can listen to sound through a receiver instead of the TV speaker.
TV Air 28
Recevier: On
Connect Recorder
Setup
Move Enter
Exit

Check Points before Requesting Service

Symptom
Anynet+ does not work.
I want to start Anynet+.
I want to exit Anynet+.
The Connecting to Anynet+
device... message appears on the
screen.
The Anynet+ device does not play.
The connected device is not
displayed.
The TV program cannot be
recorded.
1. Press the Anynet+ button.
Press the ... ... or † † button to select Receiver, then press the ENTER button.
2. Press the œ or √ button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
3. Press the EXIT button to exit.
➢
When the receiver is set to On, you can listen to the TV sound through the 2-channel(Stereo)
Sound. This is not always true. When TV is displaying DTV(air) TV can send out 5.1 channel
sound through SPDIF. But when the source is DVD(for example), TV can receive only 2 channel
sound using HDMI. In that case, 2 channel sound is only transmitted to the Receiver through
SPDIF.
➢
If the receiver is exclusively for a home theater only (supporting audio only), it may not
appear in the device list.
➢
In case of a content with copyright problem, listening through the receiver may not
properly operate.
➢
When listening through the receiver, there are restrictions for using the PIP and audio-related
menu.
Solutiona
■
Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices
only.
■
Connect only one receiver (home theater).
■
Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device's Video/Audio/HDMI Cable connections.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■
Check whether the TV remote control is in TV mode.
■
Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn't work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI Cable, please make sure to search devices
again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
■ Check if the Anynet+ device is properly connected to the TV and check if the Anynet+
(HDMI-CEC) is set to On in the Anynet+ Setup menu.
■ Press the TV button on the TV remote control to switch to TV. Then press the Anynet+
button to show the Anynet+ menu and select a menu you want.
■
Select View TV in Anynet+ menu.
■ Press the SOURCE button on the TV remote control and select a device other than
Anynet+ devices.
■
Press any of CH, CH LIST, PRE-CH, and such to change to the TV mode.
(Note that the channel button operates only when an Anynet+ device with a built-in tuner
is not connected.)
■ You cannot use the remote control when you are configuring Anynet+ or switching to a
view mode.
■ Use the remote control when the Anynet+ setting or switching to view mode is complete.
■ You cannot use the play function when Plug & Play is in progress.
■ Check whether or not the device supports Anynet+ functions.
■
Check whether or not the HDMI Cable is properly connected.
■
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI Cable only. Some HDMI cables
may not support Anynet+ functions.
■ Check whether the antenna jack on the recording device is properly connected.
English-52