Unimark SPRITE Quick Reference Manual

71U-1405-500; REV B

Control Panel

LCD
2 lines X
8 characters

Loading Stock

The Unit is equipped with two external stock inputs.
1. Verify the power switch is in the I (ON) position and
the unit has completed initialization.
2. Position the ticket stock box(es) behind the printer in
line with the ticket inputs for Bin A and Bin B. Refer
to figure for orientation.
3. Insert the ticket stock into the input. Thermal printing
surface must face down, and the staple stub must be
inserted first.
In this orientation, the magnetic stripe (if applicable)
on the back of the coupon will be facing up.
4. As the stock is inserted, the bin motor will begin to
run.
5. Release the stock when the bin motor begins to pull it
into the printer. The stock will be automatically
positioned for use.
5. Repeat the above procedure for the other bin.
6. Check the LCD display; if the unit is Off-line, place it
On-line by pressing the
Locked Stock Bin
The Unit will come equipped with a
locked stock box. To install, perform
the following:
1. Locate the stock bin and use the
keys provided to open the door.
2. Locate the two captive thumbscrews
inside the stock bin.
3. Locate the stock bin behind the unit
and line up the thumbscrews with
the brass inserts in the Unit's main
case.
4. Screw in the thumbscrews until hand
tight.
SPRITE QUICK REFERENCE GUIDE
Push-button
LED
ONLINE
Indicators
ENTER
MENU
Push-Buttons
MENU
RESET
EXIT
ON-LINE/ENTER key
The stock bin may be configured to hold two (2)
secured stacks of 500 coupons for each bin:
1. Install the removable shelf as shown in the
figure above.
2. The stock bin can now be loaded with two
stacks of 500 coupons each, both of which
are secured when the door is closed and
locked.
3. Load stock into the stock bin and load bin
inputs as defined in the previous section.
Function
Toggles the Unit between on-line
and off-line. When off-line, it is
used to accept an off-line menu
selection or to accept a field entry
option.
Initiates menu operations when
Unit is off-line. Steps through
menu selections for Unit
configuration and setup.
Initiates menu operations when
Unit is off-line. Steps through
menu selections for Unit
configuration and setup.
Resets the Unit following an error
indication when unit is on-line.
When off-line, it is used to exit the
menu level.
NOTE
Load stock with thermal
face down and binding or
staple stub first
500
BIN A
500
BIN B
LED
LED
Function
Color
Indicator
Illuminated when the Unit power switch is ON.
POWER Green
illuminated, power is OFF.
When illuminated, the Unit is on-line and ready to receive data from
the CRS. When not illuminated, the Unit is off-line and cannot
ONLINE Green
receive data, or an alarm state exists (error occurred or Unit is out of
stock). When flashing, Unit is receiving data.
Illuminates when the selected input bin (A or B) is out of stock.
STOCK Amber
Illuminates when the Unit diagnostic program detects an alarm
ERROR Red
condition, such as a ticket stock jam
BIN B External Input
Shelf Storage
The stock bin may be configured to hold one (1)
secured stack of 1000 coupons for Bin A and
another unsecured stack of 1000 coupons for Bin B:
1. Remove the shelf and place in the bottom of the
stock bin as shown in the figure above.
2. If using Bin B, slide the Bin B entry latch and
flip the entry point door down.
3. Load stock into the stock bin for Bin A only and
stock for Bin B if applicable directly behind the
stock bin. Load bin inputs as defined in the
previous section.
Page 1 of 2
Control Panel
Liquid Crystal
Display (LCD)
Push-Buttons
Output Bin
Power Switch (on
back panel)
When not
LOCK
BIN B
INPUT
BIN A
INPUT
ENCLOSURE
DOOR
1000 BIN A