Laguna Tools Laser MX Owner's Manual

Laguna Tools Laser MX Owner's Manual

X series c02 laser

Advertisement

X|Series C02 Laser
Owner's Manual
MCNCLTLCO2MU2012-40W, MCNCLTLCO2EC2436-80W, MCNCLTLCO2EC3652-150W
Precision CO2 Laser Engraving & Cutting Machine
8/27/2018
2072 Alton Parkway Irvine, CA 92606 U.S.A.
Service: +1 (949) 474-1200 or email customerservice@lagunatools.com
CO2 Laser Machine © 2018 Laguna Tools 8/27/2018

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Laser MX and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Laguna Tools Laser MX

  • Page 1 X|Series C02 Laser Owner's Manual MCNCLTLCO2MU2012-40W, MCNCLTLCO2EC2436-80W, MCNCLTLCO2EC3652-150W 2072 Alton Parkway Irvine, CA 92606 U.S.A. Service: +1 (949) 474-1200 or email customerservice@lagunatools.com CO2 Laser Machine © 2018 Laguna Tools 8/27/2018 Precision CO2 Laser Engraving & Cutting Machine 8/27/2018...
  • Page 2: Table Of Contents

    No part of this publication may be reproduced, transmitted, or translated into any language in any form by any means without our written permission. Errors and omissions may be current. CO2 Laser Machine ©2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved. 8/27/2018...
  • Page 3: Saftey

    Nonslip footwear is recommended. Wear protective hair covering to contain long hair. 12. Never modify this machine in any way. 13. Always use proper personal protective equipment when using this machine. CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 4: Warranty

    The owner's responsibility includes this warranty unless otherwise stated by Laguna Tools. These parts are designed to be used at the expense of the operator and are available for replacement or inventory purchase. The determination of a consumable part will but is not limited to the proper installation of the product in a safe environment, be made on a case-by-case basis by Laguna Tools.
  • Page 5: Reference

    In addition, convenient WiFi controls, Net Weight 220LB (100kg) 440LB (200kg) 705 LB (320kg) automatic focusing, precision linear guide rails, and more features come together to Shipping Weight CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 6 8.66" (220 mm) Focal Lens Diameter 20mm 20mm 20mm 1.1.5 Fume Extraction Dust Port Outer Diameter 3.95" (100mm) 2x 5.95 (150mm) 5.95 (150mm) 400CFM Fume CFM Requirement 400CFM 600CFM 600CFM Debris (lower) CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 7: Dimensions

    The ribs can also be removed and replaced. TX (SKU1) Fig C025: EX Laser machine capacities and dimensional drawing. Fig C023: TX Laser machine capacities and dimensional drawing. CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 8: Control & Display Elements

    Set speed of current layer Pulse laser control. NOTICE! Pressing the pulse key will fire the laser beam. Use caution not to damage workpiece. Reset the controller and return to the home position. CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 9: Accessories & Options

    Q: Is this a consumable product? In other words, does the laser ruin the honeycomb? A: Each laser machine that Laguna Tools sells comes with an auxiliary blower. If the A: A mark will be left as the laser passes through, but each side will last for a very machine does not have a fume extractor, the blower is used to move the fumes to a long time.
  • Page 10: Setup

    Only cut deep enough to cut the tape or use a dull edge. 2. Organize the hardware and setup tools needed (at beginning of each setup section) prior to proceeding with setup. CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 11: Connection Diagrams

    For further electrical how to set up each axillary unit in the following setup sections. For further electrical diagrams, see A1. Wiring diagrams, see A1. Wiring CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 12: Unboxing & Inventory

    Universal Connector. (4.7) Spare Limit Switch. (4.8) Alignment Cross-hairs. (4.9) Water attachments. Hose Clamps. (4.10) Exhaust Hose Clamps. NOT SHOWN: Used to connect the compressor and the Air Inlet on Laser Air Hose machine. CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 13: Machine Set-Up

    2. Remove the (3) four screws on the (1) Laser Tube Cover. knife when remove the zip ties on belts to avoid damaging the belts. 3. Position the Laser tube cover and re-install the screws.. Tools Needed: Scissors. CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 14: Installing The Laser Tube

    - DO NOT over-tighten. DO NOT adjust the height or Connect the (2.2) anode wire to the laser tube with the phillips head connection position of the tube mounts at this time. screw. CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 15: Auxiliary Equipment Setup

    Some of these accessories are Mounting Bolt Holes. (4) TEFC AC Induction Motor. designed to fit multiple machines offered by Laguna Tools, check the specification sheet for a fit guide of all X-Series Laser accessories.
  • Page 16: Water Chiller & Pump

    4. Connect the water outlet to the machine inlet according to the connection diagram. 5. Connect the alarm cable to the laser machine [7]. 6. Do not connect to power until set-up is complete. CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 17: Maintenance

    Replacement Parts - Many of the replacement parts can be purchased from several Focal Lens different sources. There are no components in the machine that are proprietary to Laguna Tools - making it easier for the service technician to find replacement parts like belts, motors, mirrors, mounts, and electronics. 3.1 Service Schedule If Focal Lens is dirty - Check the air supply, air valves, and all air connections.
  • Page 18: Maintenance Work

    Y-axis limit. To test only X-axis mirror alignment (mirror 2 & 3), start at (0,0,0) and end at (X-limit,0,0). Similar for testing only Y axis limit. Figure C035: Checking for Alignment. CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 19: Mirror Alignment

    4. Align the laser tube to mirror 2 by adjusting the height of the laser tube. 5. Align the laser tube to mirror 3 by adjusting the height of the laser tube. 6. Check alignment and adjust as needed. CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 20: Focal Lens

    The pre-installed lens is 20mm in diameter, made of ZnSe through the partical vaper deposition process (PVD), and has a focal length of 50.8mm. The lens should be checked often for cleanliness and can be changed for lenses of different purpose. Lenses CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 21: Troubleshooting

    A: The water should be changed on a monthly (30 days) basis. The water can be left in the tube as long as the water cannot freeze. If you are operating this laser in CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 22: A1. Parameters

    200 - 100% Cut 1/4" (6.4mm) 5 - 100% 15 - 100% 25 - 100% 50 - 100% Cut 3/8” (9.5mm) 5 - 100% 40 - 100% Cut 1/2" (12.7mm) 5 - 100% CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 23: A2. Parts

    WARNING! Never perform and setup, maintenance or adjustments with the machine connected to the power Silicone, Vulcanized Rubber, Polyurethane, Neoprene, Gaskets, Rubber Rubber source! vibration mats, Rubber stamps NOTICE! Only use authentic Laguna Tools parts for replacements. Engrave 100 - 80% 200 - 80% 325 – 80% 400 –...
  • Page 24 A3. Wiring CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 25 A3. Wiring CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 26 Starter Switch Debris Maintenance Design Software Integration (not included) Maintenance Work U.S II-VI Optical Lenses Mirror Alignment Dimensions Un-boxing Mirror Allignment Dust Debris Extraction Dust Port Outer Diameter Ventilation Net Weight Voltage CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...
  • Page 27 No part of this publication may be reproduced, transmitted, or translated into any language in any form by any means without our written permission. Errors and omissions may be current. CO2 Laser Machine ©2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved. 8/27/2018...
  • Page 28 Lagunatools.com 2072 Alton Parkway Irvine, CA 92606 U.S.A. For Customer Service: +1 (949) 474-1200 or email customerservice@lagunatools.com CO2 Laser Machine © 2018 Laguna Tools 8/27/2018...

This manual is also suitable for:

Laser txLaser ex

Table of Contents

Save PDF