1. Manuals
  2. Brands
  3. FAR Manuals
  4. Other
  5. RAC 171
  6. Translation of original instruction manual

FAR RAC171 Translation Of Original Instruction Manual

Oil pneumatic riveting tool
Hide thumbs Also See for RAC171:
1
2
3
4
5
6
7

Advertisement

Table of Contents

 
 
TRANSLATION OF ORIGINAL INSTRUCTIONS
OIL PNEUMATIC RIVETING TOOL
FOR RIVETS Ø 4.8 * - Ø 7.8 ** ( * ALUMINIUM EXCLUDED
** ALUMINIUM ONLY)
FARBOLT, MAGNA-LOK®, MONOBOLT® Ø 4.8 (3/16") - Ø 6.4 (1/4")
INSTRUCTIONS FOR USE
www.air-allied.com.au
sales@air-allied.com.au
www.air-allied.com.au

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RAC171 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for FAR RAC171

Summary of Contents for FAR RAC171

  • Page 1     TRANSLATION OF ORIGINAL INSTRUCTIONS OIL PNEUMATIC RIVETING TOOL FOR RIVETS Ø 4.8 * - Ø 7.8 ** ( * ALUMINIUM EXCLUDED ** ALUMINIUM ONLY) FARBOLT, MAGNA-LOK®, MONOBOLT® Ø 4.8 (3/16") - Ø 6.4 (1/4") INSTRUCTIONS FOR USE www.air-allied.com.au sales@air-allied.com.au www.air-allied.com.au...
  • Page 2 The undersigned Far S.r.l., having its office in Quarto lnferiore (BO), Via Giovanni XXIII No. 2, herewith DECLARES on its sole responsibility that the riveting machine Type: RAC 171- Hydropneumatic tool Application: for rivets diameter. 4.8—7.8 (4.8 aluminium excluded) which is the object of this declaration complies with the basic safety requirements established in the law decree Leg.

  • Page 3: General Notes And Use

    The tool must be used for rivets diam. 4.8 (aluminium excluded) - 7.8 mm (aluminium only). The riveting tool RAC171 can also work with rivets type FARBOLT, MONOBOLT® and MAGNA-LOK® Ø 4.8 (3/16”) - Ø 6.4 (1/4”) by previous replacement of nozzles, cone and clamps.
  • Page 4 DISPOSAL OF THE RIVETING TOOL • Do not carry the connected tool by pulling the hose. The hole must be far from any heating sources or from cutting GUARANTEE parts. • Keep the tools in good conditions; do not remove either FAR riveting tools are covered by a 12-month warranty.

  • Page 5: Tool Identification

    TECHNICAL DATA TOOL IDENTIFICATION 6 BAR  Working pressure The riveting tool RAC 171 is identified from a marking that shows company name and address of manufacturer, desig- Min. diam =  Min. int. diam. Of the compressed air feed- nation of the tool, CE mark and year of manufacturing.
  • Page 6 TOPPING UP THE OIL-DYNAMIC CIRCUIT (fig. f8) You need to top up the oil-dynamic circuit after a long period of work, when you note a power loss. Put the riveting tool (DWELL AND NOT FED) in a horizontal position and remove the plug (F), by means of a 5 mm Allen wrench (equipped with the riveting tool);...

  • Page 7: Disposal Of The Riveting Tool

    18 mm and 14 mm, remove the chuck (M) and extract the clamps (N). The riveting tool is supplied, besides the nozzle series for FAR rivets, with a series of accessories for using the rivets type FARBOLT, MONOBOLT® and MAGNA-LOK®, respectively of Ø...

Table of Contents