Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for ZKTeco FHT2311
Summary of Contents for ZKTeco FHT2311
- Page 1 USER MANUAL Full Height Turnstile Applicable Models: FHT 2300 / 2400...
-
Page 2: Table Of Contents
Contents Chapter 1 Product Introduction ......................1 1.1 Model number and access control ..................1 1.2 Structures and dimensions ....................1 1.3 Mechanical system of FHT2300&FHT2400 series ..............2 1.4 Electronic control system ..................... 2 1.5 The working principle of full height turnstiles ..............3 1.6 Product related parameters .................... -
Page 3: Chapter 1 Product Introduction
1.1 Model number and access control Access C3-200 with two KR101E InBio260 with two FR1200/ID reader reader Model √ FHT2300 √ FHT2311 √ FHT2322 √ FHT2400 √ FHT2411 √ FHT2422 1.2 Structures and dimensions FHT2000 series has stainless steel casing, which provides corrosion resistance and durability. -
Page 4: Mechanical System Of Fht2300&Fht2400 Series
FHT2400’s appearance and dimensions are as shown in Figure 1-2B： Figure 1-2B 1.3 Mechanical system of FHT2300&FHT2400 series The mechanical system of the full height turnstiles includes a mainframe box and a frame. The direction indicator, core, control panel, access controller and lock are installed in the mainframe box. The core component mainly consists of two solenoids, a spring and a transmission mechanism. -
Page 5: The Working Principle Of Full Height Turnstiles
1.5 The working principle of full height turnstiles 1.5.1 After the power is turned on, the system will perform self-check. If no fault is detected, the device will operate as usual. If a fault is detected, the system will display the related messages on the LCD screen. -
Page 6: Chapter 2 The Installation Of The Device
Chapter 2 The Installation of the Device 2.1 Installation notes 2.1.1 It is recommended that the full height turnstile should be installed on a cement platform with 50mm to 100mm in height. 2.1.2 It is recommended that the full height turnstile should not be used in corrosive environments. 2.1.3 Make sure the earth wire of the system is connected reliably reliably to prevent any personal injuries or other accidents. - Page 7 conduit, the conduit mouth needs to be bent back. FHT2300&FHT2400 series installation holes are as shown in Figure 2-3A and Figure 2-3B. Ø25 PVC pipe 2-3A Figure Ø25 PVC pipe 2-3B Figure...
- Page 8 Put the installation diagram on the floor. Using percussion to drill holes for M12 screws on the corresponding position. Then install the screws to the corresponding positions. Next, place the frame on top of the screw and fix it. After that, the mainframe-box is fixed on the frame. Finally install the whole rotating part in the middle of the frame as shown in Figure 2-3C.
- Page 9 Figure2-3D...
-
Page 10: Chapter 3 Menu Operation
Chapter 3 Menu Operation 3.1 Menu operation 1. After start-up, the LCD screen will display the current working mode. 2. There are 7 buttons on the panel: “”LEFT OPEN”, “ RIGHT OPEN”, “ MENU”, “UP”, “DOWN”, “OK” and “ESC”. 3. There is a RS232 communication Interface on the panel that can send a signal to the panel. 3.2 Button instruction LEFT OPEN: Open the device to right. -
Page 11: System Menu Description
3.4 System menu description 1. Device mode （1）Full height turnstile 2. Direction setting ① → exit, entry ← ② → entry, exit ← The setting of the sides for entry or exit. "→ exit, entry ←" means that right side is exit and left is entry. - Page 12 6. Reset counters Resetting the entry / exit passing counter. 7. System initialization After successful initialization, the panel parameters will be restored to the factory setting and the entry / exit passing counter will be reset. 8. Device number Press "UP" and "DOWN" buttons to adjust values. Press "OK" button to save. When plural devices are placed together, different device number can be used to distinguish, the default number is 1.
-
Page 13: Chapter 4 Product Maintenance
Chapter 4 Product Maintenance 4.1 Mainframe-box maintenance The mainframe-box is made of 304 stainless steels. So after a long period of operation, its surface may have some stains. It can use gauze to clean the mainframe-box. In order to protect the lines of surface, please wipe along the lines direction.