Page 1
1" Elima-Matic Bolted Metal – UL Listed with Metallic Center Sections E1 Metallic Pumps • Aluminum • Stainless Steel VERSA-MATIC ® • Warren Rupp, Inc. • A Unit of IDEX Corporation 800 North Main Street, Mansfield, OH 44902 USA • Phone: (419) 526-7296 • www.versamatic.com...
Safety Information IMPORTANT WARNING When used for toxic or aggressive fluids, the pump should Read the safety warnings and instructions in this manual always be flushed clean prior to disassembly. before pump installation and start-up. Failure to comply with the recommendations stated in this manual could damage the pump and void factory warranty.
Page 4
A Aluminum w/ PTFE O-rings S Stainless Steel S Stainless Steel w/ PTFE O-rings Options: C Carbon Steel w/ PTFE O-rings H Hastelloy C w/ PTFE O-rings UL UL T PTFE Encapsulated Silicone O-rings ATEX ATEX versamatic • Model E1 Metallic Bolted e1mdlHsmATEXUL-rev0317...
Page 5
Commonly referred to as 316 Stainless Steel in the pump industry. For specific applications, always consult the Chemical Resistance Chart. Model E1 Metallic Bolted • versamatic e1mdlHsmATEXUL-rev0317...
Page 6
The UL Listed Pump The E1-UL pump model had been tested by Underwriters Laboratories, Inc. and is in compliance with the safety specifications for air-operated pumps for use in the transfer of flammable liquids. This pump has been rated for use in pumping the following liquids:...
Page 8
(flooded suction condition), pipe the exhaust higher than the product source to prevent siphoning spills. 1" DIAMETER AIR LIQUID EXHAUST PIPING LEVEL SUCTION LINE versamatic • Model E1 Metallic Bolted e1mdlHsmATEXUL-rev0317...
To start the pump, slightly open the air shut-off valve. After the pump primes, the air valve can be opened to increase air flow as desired. If opening the valve increases cycling rate, but does not increase the rate of flow, cavitation has occurred. The valve should be closed slightly to obtain the most efficient air flow to pump flow ratio. Model E1 Metallic Bolted • versamatic e1mdlHsmATEXUL-rev0317...
Inspect check valves and seats for wear and proper setting. Replace if necessary. Entrained air or vapor lock in chamber(s). Purge chambers through tapped chamber vent plugs. For additional troubleshooting tips contact After Sales Support at service.warrenrupp@idexcorp.com or 419-524-8388 versamatic • Model E1 Metallic Bolted e1mdlHsmATEXUL-rev0317...
Page 13
Versa-Matic warrants to the original end-use purchaser that no product sold by Versa-Matic that bears a Versa-Matic brand shall fail under normal use and service due to a defect in material or workmanship within five years from the date of shipment from Versa-Matic’s factory.
Page 14
EC / EU DECLARATION OF CONFORMITY The objective of the declaration described is in conformity with the relevant Union harmonisation legislation: Directive 94/9/EC (until April 19, 2016) and Directive 2014/34/EU (from April 20, 2016). Date of Issue: 10 May 2014 Technical File No.: 203104000-1410/MER Quality System Registration No: ISO 9001-2000 Conforming Apparatus: Air-Operated Metal Double Diaphragm Pumps for Use In Potentially Explosive Atmospheres...
Page 15
INNER PLATE (PTFE FITTED PUMPS ONLY) PARTS BEING REPLACED WITH Item # Part Number Description Qty. E101B RETAINER P24-106P PILOT SPACER P24-107 PILOT VALVE O-RING P24-108 JAM NUT P50-112 PILOT SHAFT V181TI INNER PLATE (PTFE FITTED PUMPS ONLY) Model E1 Metallic Bolted • versamatic e1mdlHsmATEXUL-rev0317...