Download
Share
Print this page
Pride Mobility Zeus 260/440lb Fitting Instructions Manual
  1. Manuals
  2. Brands
  3. Pride Mobility Manuals
  4. Lifting Systems
  5. Zeus 260/440lb
  6. Fitting instructions manual
Pride Mobility Zeus 260/440lb Fitting Instructions Manual

Pride Mobility Zeus 260/440lb Fitting Instructions Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
260/440lb
AFFIX BARCODE LABEL
HERE

Advertisement

loading
Need help?

Need help?

Do you have a question about the Zeus 260/440lb and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Pride Mobility Zeus 260/440lb

Summary of Contents for Pride Mobility Zeus 260/440lb

  • Page 1 260/440lb AFFIX BARCODE LABEL HERE...
  • Page 2 The latest/current version of this manual is available on our website. NOTE: This product is compliant with WEEE, RoHS, and REACH directives and requirements. Manufactured By: Distributed By: Autochair Ltd Pride Mobility Product, Corp. Wood Street North 182 Susquehanna Avenue Copyright © 2017 Meadowlane Ind. Est.

  • Page 3: Table Of Contents

    C O N T E N T S INTRODUCTION ........................4 SAFETY ............................ 5 III. TECHNICAL …......................... 8 FITTING INSTRUCTIONS ....................9 WIRING ............................ 13 INSTALLING & REMOVING …..................15 VII. TROUBLESHOOTING ......................17 VIII. WARRANTY ......................... 18 www.pridemobility.com...

  • Page 4: Introduction

    I N T R O D U C T I O N Welcome to Pride Mobility Products. Congratulations on the purchase of your new lift system. The lift system design combines the most advanced state-of-the-art components with modern, attractive styling.

  • Page 5: Safety

    I I . S A F E T Y PRODUCT SAFETY SYMBOLS The symbols below are used on the lift system to identify warnings and mandatory or prohibited actions. It is very important for you to read and understand them completely. Read and follow the information in the owner’s manual.
  • Page 6 I I . S A F E T Y LIFTING CAPABILITIES The lift system is designed to lift a maximum weight of 260 lbs. (120 kg) or 440 lbs. (200kg) depending on the model purchased. Check this by referring to labels on the lift arm. Under no circumstances should the lift system be made to exceed this weight limit.
  • Page 7 I I . S A F E T Y TRANSPORT VEHICLE POSITIONING Be sure your vehicle is parked on flat, level ground and the emergency brake is engaged before attempting to lift a mobility product. WARNING! Attempting to lift a mobility product when a vehicle is not on level ground will cause the mobility product to swing toward or away from the vehicle, making it difficult to get the mobility product into the vehicle.

  • Page 8: Technical

    I I I . T E C H N I C A L PRODUCT SPECIFICATION Model / SWL 440 lbs (200kg) 260 lbs (120kg) 24.2lbs (11kg) Weight of the lifting arm: 30.8lbs (14kg) 260lbs (120kg) Maximum lifting capacity, SWL: 440lbs (200kg) Power supply: 12V dc Maximum current draw:...

  • Page 9: Fitting Instructions

    I V . F I T T I N G I N S T R U C T I O N S The hoist is tested and set to a nominal position for the vehicle it is intended for. Adjustment may then be required to suit the vehicle.
  • Page 10 I V . F I T T I N G I N S T R U C T I O N S Setting the Boom (Vertical Extension) 1. The hoist will be provided assembled and set to a nominal boom size suitable for the vehicle. If a more optimal boom setting is required the following procedure can be used.
  • Page 11 I V . F I T T I N G I N S T R U C T I O N S The limits of the adjustments are shown on the previous diagrams. The maximum settings must not be exceeded. When correctly set, the top part of the hoist must be parallel with the vehicle floor, when the actuator is fully retracted.
  • Page 12 I V . F I T T I N G I N S T R U C T I O N S TORQUE SETTINGS This screw is factory set and not adjustable. NOTE: Only use the screws supplied as these have pre-applied thread locking compound. When tightening the screws, the screws should be tightened slowly and evenly until the desired torque setting is reached.

  • Page 13: Wiring

    V . W I R I N G HARD WIRING THE CONTROL BOX • The wiring supplied for connecting the battery and power socket is twin core with red and black insulation. • Run the cable down the brace bar and through the bulkhead (use the grommet supplied if required) to the vehicle battery.
  • Page 14 V . W I R I N G CONNECTING ACTUATORS Test operation with handset. If the movement is opposite to expected then reverse the polarity of the connector/s. REVERSING POLARITY www.pridemobility.com...

  • Page 15: Installing & Removing

    V I . I N S T A L L I N G A N D R E M O V I N G INSTALLING 1. Rest the upper mounting lug onto the longer upper pin before aligning the lower pin. The hoist should slide smoothly down into place.
  • Page 16 V I . I N S T A L L I N G A N D R E M O V I N G REMOVING 1. Ensure the system power is OFF 2. Unclip the power connectors 3. Remove retaining clip 4.

  • Page 17: Troubleshooting

    V I I . T R O U B L E S H O O T I N G TROUBLESHOOTING & FREQUENTLY ASKED QUESTIONS PROBLEM SUGGESTIONS • Make sure that the hoist is switched on. • Turn the hoist off and back on again and retry. •...

  • Page 18: Warranty

    V I I I . W A R R A N T Y The warranty period for your hoist is 12 months from the date of delivery. This warranty will cover any defects of workmanship or function. The warranty does not cover any incorrectly installed hoist’s or one with damaged mechanical or electrical components due to incorrect use or damage.
  • Page 19 N O T E S www.pridemobility.com...
  • Page 20 www.pridemobility.com...