Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Weber Maschinentechnik GmbH CR 7 HD
- Page 1 Operating and Maintenance Manual CR 7 HD Honda GX 390 Weber Maschinentechnik GmbH Im Boden 5 - 8, 10 57334 Bad Laasphe-Rückershausen / Germany Telephone +49 (0) 27 54 / 398-0 Fax +49 (0) 27 54 / 398-101 E-Mail: info@webermt.de Web: www.webermt.de...
- Page 2 CR 7 HD...
-
Page 3: Table Of Contents
Table of contents Introduction Safety guidelines Graphic presentation Device description Technical data Activities prior to starting work Starting Compacting Shutting down Maintenance overview Maintenance work Operating fluids and fill levels Troubleshooting Storage Contact addresses CR 7 HD... -
Page 4: Introduction
You can obtain information on the assembled Honda gasoline engine and find a spare-part list for it at www.honda-engines-eu.com. The valid conformity declaration is enclosed with every machine delivery. CR 7 HD... -
Page 5: Safety Guidelines
This machine is capable of exceeding the permissible sound level of 80 dB(A). The owner might also face additional dangers when using the machine. Precautionary action must, therefore, be taken. Protective equipment includes: Hearing protection Hard hat Safety shoes Protective gloves CR 7 HD... - Page 6 Do not position yourself or work under suspended loads. If lubricating oils and fuel come into contact with skin, they can cause skin cancer. Upon contact with the skin, clean affected skin with suitable cleaning agent without delay. CR 7 HD...
- Page 7 Important information for operating and maintenance personnel is marked by pictograms. Warning against irritants or materials hazardous to health Warning against a hazardous place Warning against a suspended load Wear ear protection General regulation Environmental protection Hard hat Safety shoes Protective gloves CR 7 HD...
-
Page 8: Graphic Presentation
Graphic presentation Overall view CR 7HD 1 Engine 2 Drive lever 3 Manual guidance rod 4 Lifting ring 5 Base plate 6 Protective frame 7 Exciter 8 Gas lever 9 Attachment plates 10 Hearing protection (sticker) CR 7 HD... -
Page 9: Device Description
After starting, vibration is switched on via the centrifugal clutch attached to the engine. Use the gas lever to vary the engine speed between idle and full throttle. Forward and reverse is variably controlled via the handle attached to the manual guidance rod. CR 7 HD... -
Page 10: Technical Data
Technical data CR 7 HD Weight Operating weight CECE in kg 437 / 489 Dimensions 1835 Overall length (in mm) 600 / 800 Width with attachment plates (in mm) 1135 Height with folded manual guidance rod (in mm) Base plate length (base in mm) - Page 11 1 Description 2 TYPE ......................3 Serial number 4 Year of construction ......................5 Mass 6 Rated power kW ......................CR 7 HD...
-
Page 12: Activities Prior To Starting Work
(1). Checking the engine oil level pull Open the engine hood (1). Pull the oil dip stick (1) out of the crankcase. The correct oil level is between the min. and max. marks. CR 7 HD... - Page 13 Tighten the screws (1) of the attachment plates with a torque of 425 NM. Installing the protective mat Fasten the protective mat with holder, screws, spring-lock washers and nuts on the base plate front and rear. Ensure that the protective mat rests under the base plate. CR 7 HD...
-
Page 14: Starting
Slowly tighten the handle (1) of the reversing starter until resistance is noticeable. Allow the handle (1) to glide back into the initial position, and then forcefully and completely pull it through with both hands. Allow the engine to warm up for a few minutes. CR 7 HD... -
Page 15: Compacting
Turn the short-circuit button to the “0” – OFF position. Close the fuel cock (1). During breaks – even if they are short – the machine must be shut down. Parked devices that represent an obstacle must be safeguarded against through conspicuous measures. CR 7 HD... -
Page 16: Maintenance Overview
If lubricating oils and fuel come into contact with skin, they can cause skin cancer. Upon contact with the skin, clean affected skin with suitable cleaning agent without delay. If accessible during maintenance, check the condition and stability of all screws. CR 7 HD... -
Page 17: Maintenance Work
Clean air filter insert as specified by the engine manufacturer if there is damage or if it is extremely dirty. Dispose of oils, greases, cloths soaked in oil, and re- placed parts with oil on them in an environmentally friendly manner. CR 7 HD... - Page 18 Checking the V-belt Remove the V-belt guard (1). Check the V-belt (1) for cracks, damaged flanks, and wear. If there is excessive wear – replace the V-belt as specified in the repair manual. CR 7 HD...
-
Page 19: Operating Fluids And Fill Levels
Operating fluids and fill levels Assembly Operating material Quantity Summer Winter CR 7 HD Quality Engine Engine oil SAE 10 W 40 1.1 l (– 10 ~ + 50 °C) API – CD CE-CF-CG or SHPD or CCMC – D4 – D5 – PD2... -
Page 20: Storage
All bare parts / accelerator / – Oil / grease accelerator control cable / fastening bolts If the machine is to be stored for longer than six months, then contact the Weber service organization to discuss additional measures. CR 7 HD... - Page 21 CR 7 HD...
- Page 22 CR 7 HD...
- Page 23 South - WEBER Maschinentechnik do Brasil Telefon + 55 (0) 51- 587 3044 America Rua João Werno Erhart, 4691 Telefax + 55 (0) 51- 587 2271 Bairro Rincão 93310-405 Novo Hamburgo /RS E-Mail webermt.@webermt.com.br Brasil CR 7 HD...
-
Page 24: Contact Addresses
> Vibrating tampers > Vibration rollers > Joint cutters > Internal vibrators and converters > Rollers Weber MASCHINENTECHNIK GmbH Im Boden 57334 Bad Laasphe-Rückershausen Telephone +49 (0) 27 54 / 398-0 – Fax +49 (0) 27 54 / 398-101 CR 7 HD...