Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Interlogix truVision 11c Series
Summary of Contents for Interlogix truVision 11c Series
- Page 1 DVR Installation Manual 1/2/2014 V1.1 truVision 11c Series DVR’s...
-
Page 2: Table Of Contents
This manual will provide assistance in setting up I-View Video Verification functionality based on sensor events configured in the interlogix truVision 11c. It is not a replacement for the excellent manuals for the interlogix truVision 11c, which can be downloaded from their site at http://www.interlogix.com/video/product/truvision-dvr-11/. -
Page 3: Introduction
PC or tablet device’s browser. With each clip is the ability to see one or more “Live Views” for various cameras associated with the DVR that generated the SMTP alarm. Figure 1 interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 3... -
Page 4: Workflow
I-Viewnow.com portal. 8. Trouble Shooting: This section is provided to help the technician troubleshoot common problems encountered while installing this particular type of DVR. interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 4... -
Page 5: Installation Worksheet
I-View servers. The IT Site Administration must enable port forwarding from their router/firewalls to the Speco DS 16 DVR port address. interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 5... -
Page 6: Default Dvr Login
VGA Cable USB Mouse VGA Port Although a keyboard can be used it’s not required as the system will provide for mouse selection of alpha-numeric characters. interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 6... -
Page 7: Firmware Version
The version of the firmware on the DVR tested with I-View Now is shown below. The DVR should have this version set to ensure proper interoperation with I-View Now. Figure 3 interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 7... -
Page 8: Network And Time Setup
The Preferred DNS server is typically 8.8.8.8 with an alternate of 4.2.2.2. Be sure to apply these and any other settings made by clicking on the “Apply” button at the bottom of the screen. interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 8... - Page 9 National Time Center. The DVR manual provides more detail on options for how to do this. You can see the default settings here after selecting the Network settings icon and selecting NTP as shown below: Figure 6 interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 9...
-
Page 10: Router Settings
1. Click the Network Settings icon in the menu toolbar and then click More Settings. Figure 7 2. Enter the RSTP port value. The default value is 554. 3. Click Apply to save the settings. interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 10... -
Page 11: Smtp Settings
SMTP. The full test is when an alarm contact is closed and a message is sent to I-View with the corresponding interaction with I-View to provide Live View and Video Clips. interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. -
Page 12: User Settings
DVR’s password in order to allow I-View to programmatically log onto the DVR when requesting clips or initiating Live View. interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 12... -
Page 13: Recording Setup
Recording Setup The Interlogix truVision DVR supports various recording modes which can be enabled via the user interface for the DVR. Before you can set up the DVR to begin recording, you must configure general recording settings for the analog cameras. -
Page 14: Scheduled Recording Mode
Pre-record and Post-record parameters are set to an interval that exceeds the minimum pre and post alarm video time recording intervals that the I-View system will attempt to retrieve and show as a clip for the user. interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 14... -
Page 15: Alarm Actions And Input Setup
6. In the Rule window, click Trigger channel and select the cameras to be triggered for recording when an alarm is detected. Only analog cameras can be selected. Click Apply to save the settings. Figure 12 interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 15... -
Page 16: Event Recording
The Encoding screen is used to setup the recording parameters for the video stream of the cameras to disk as well as the amount of pre and post alarm event recording. For I-View integration both values should be set to 10 seconds. Figure 14 interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 16... -
Page 17: Configure I-View Now Entry Delays
Configure I-View Now Entry Delays Entry Delays are configurable through the I-View Now Dealer Portal. Log in to configure. interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 17... -
Page 18: Test Settings
For example, if relay 1, connected to input 1 on the DVR is supposed to trigger when a panic button is pushed, ensure not only that the DVR has received the signal, but that the i-viewnow.com portal has received the signal and correctly identifies the type of alarm. interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 18... -
Page 19: Troubleshooting
This section is provided to help the technician troubleshoot common problems encountered while configuring the Interlogix truVision DVR to talk to I-View. A recommended setting for the cameras is CIF with a frame rate of approximately 6 per second. This provides a good balance of quality and bandwidth resolution. -
Page 20: Glossary
Internet Protocol, IPv6. 7. SMTP - Simple Mail Transfer Protocol is an Internet standard for electronic mail (e-mail) transmission across Internet Protocol (IP) networks. interlogix truVision DVR 11c © 2014 I-View Now, LLC. All Rights Reserved. Page 20...