Tavistock Equalise Installation Instructions Manual

Installation Instructions for Equalise Backlit Mirror
Please read carefully before you start and retain for future reference
SAFETY INSTRUCTIONS
(Applicable to UK Installations only)
All fittings must be installed by a competent person, in accordance
with current IEE wiring regulations. If in doubt, consult a qualified
electrician.
IMPORTANT
Always switch off the electrical supply at the mains during
installation and maintenance. It is recommended that the fuse is
withdrawn or the circuit breaker is switched off for the necessary
circuit before installation commences.
The product must be mounted a minimum of 150mm from an
adjacent wall or obstruction to ensure correct function of the
infrared sensor. The sensor can be repositioned if required. See
overleaf for details.
Fitting in Bathrooms is subject to the appropriate location (See
Diagram). Refer to IEE Regulations. This product is suitable for
Zones 2 and outside zones. It IS NOT suitable for installation in
Zone 0 or Zone 1. It is also not suitable for installation in Saunas,
Steam Rooms or Shower Cubicles.
This product is only suitable for permanent installation. DO NOT
connect to a trailing plug and socket outlet.
Equalise
SBL17
Although this product has an Ingress Protection rating of IP44, it is
only suitable for indoor use.
Do not attach the product to surfaces that are damp or otherwise
IMPORTANT
electrically conductive.
MIRROR LOCATION
The product should be positioned well away from curtains and other
fabrics. Never cover the mirror.
Always ensure that the correct bulb is used and that the maximum
bulb rating is not exceeded.
This product is heated, we recommend that it is turned off after use
and should never be left on for prolonged periods of time.
CARE & SAFETY
REMEMBER
150mm
Wear suitable eye protection when drilling. Take care when using
Minimum distance
power tools near water - the use of a residual current device (RCD)
is advised. Beware of hidden cables or pipes. Take care if drilling
on tiled surfaces in case the drill slips. A piece of masking tape
applied to the wall before marking out the fixing holes will stop the
drill from wandering.
WARNINGS
Infrared sensor
Do not strike glass components with hard or pointed items. Do not
place very hot or very cold items against or in close proximity to
glass surfaces unless an adequately thick insulation material is
used to prevent such items coming in contact with the glass.
The nominal thickness of the mirror glass used in this product is
5mm and is film backed for safety. If the glass becomes chipped or
broken, replace immediately. For details on replacement glass and
other components contact customer services at the address below.
This product could be dangerous and installation is only to be
carried out by a competent person.
It is recommended that the unit is cleaned with a soft dry cloth
when turned off. Never use cleaning agents or abrasive materials
on any type of surface finish. Do not allow moisture to come into
contact with the lamp.
COMPLIANCE
This product complies with the following Electrical Safety
Standards:
EN 55015:2001; BS EN 60598-1: 2004, AMD:2001, AMD:2003; BS EN
60598-2-1: 1989. EN 60529: 1992 & A1, A2, A3.
REPLACING LAMPS
WARNING
Disconnect the unit from the mains power supply before attempting
to replace a lamp. Fluorescent lamps may get hot. Ensure lamps
are sufficiently cooled before changing. Remove the mirror glass
from the body by removing the screws and washers. Disconnect the
heated pad by separating the small plug from the socket and store the
mirror in a safe place. Then pull out the 4-Pin connector that locates
on the circular fluorescent tube and gently pull out the expired
lamp from the retaining clips.
Fit the replacement tube in the retaining clips, making sure that it
is secure, and push the 4 pin connector onto the lamp.
Reconnect the heated pad and replace the glass front making
sure all screws are secure.
Tavistock Ltd, Brassmill Lane Trading Estate, Bath, BA1 3JF
T9 40W Circular
Fluorescent Tube
4 Pin
Connector
Retaining
Clip
| Tel: 01225 787870 | www.tavistock-bathrooms.co.uk
LAMP TYPE:
T9 40W Circular Fluorescent Tube.
IEE BATHROOM ZONES DIAGRAM
0.6m
0.6m
0.75m
2
1
2 2
2
2
OUTSIDE
ZONES
0.75m
TAV.EQU.01.RF