Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Innes Manuals
  4. Digital Signage
  5. DMB400
  6. User manual

Innes DMB400 User Manual

Hide thumbs Also See for DMB400:

Advertisement

Quick Links

Download this manual
User Manual
DMB400
4.10.11 001A
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the DMB400 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Innes DMB400

Summary of Contents for Innes DMB400

  • Page 1 User Manual DMB400 4.10.11 001A...
  • Page 2 Please read carefully the following instructions before switching the product on: - WARNING! Correct fitting and installation is of the utmost importance. Incorrect fitting and/or installation may result in personal injury or loss. INNES disclaims all liability, of whatever kind, if the product is assembled, fitted and/or installed in an incorrect manner.

  • Page 3: Table Of Contents

    Table of Contents Introduction Getting started with the device LEDs behaviour Connectors pin-out Technical specifications Troubleshooting Conformities Contacts...

  • Page 4: Introduction

    This device is intended to work with the supplied power supply unit. This power supply unit must be connected to a mains socket conforming to standard NF C 15-100. If the AC power cable is damaged, it must be replaced. It is possible to order a replacement mains unit by sending a request to the email address sales@innes.pro.

  • Page 5: Getting Started With The Device

    Getting started with the device Front face DMB400 ANT 3 ANT 4 DC IN AUDIO USB2 RS232 DTE HDMI1 OUT Antennas Power supply connector Audio connector USB2 3.0 connector RS232 DTE connector HDMI output connector Rear face ANT 1 ANT 2...
  • Page 6 190 mm 200 mm DMB400 ANT 3 ANT 4 DC IN AUDIO USB2 RS232 DTE HDMI OUT Labeling The model of the device, its power supply characteristics, its serial number (PSN) as well as its MAC address are written on a label stuck on the case. Additional tags may be present in case of built-in options.
  • Page 7 Device start-up step > Step 1 (T0=0s) Step 2 (T~23s) Step 3 (T~44s) Device start-up initialisation Device start-up finalisation Nominal mode This phase duration is depending on some variable values During this step, the device has to play the content. (like NTP), some network access duration or some data When firmware upgrade process occured, in checking (check-disk)

  • Page 8: Leds Behaviour

    4 seconds Error. ¹ ¹ If the problem persists despite an appropriate power-supply, contact INNES technical support. ² If the problem persists, it is advised to find out the media not supported yet by the system and remove it from content.

  • Page 9: Connectors Pin-Out

    Connectors pin-out Power supply connector (12VDC-1.2A) DMB400 DC IN AUDIO Lan connector Ethernet RJ-45. 10/100/1000 BaseT. It is recommended to use shielded cables. Stereo jack 3.5mm L+R audio cable connector It is recommended to use cables whose length is less than 3 meters.
  • Page 10 • During boot, the GPIO1 is configured in input during some seconds. And then after the system startup, the GPIO1 is operational. • The GPIO has a weak pull-up. Principle schematics for several use cases 3 wires input configuration : DMB400 3.3V Input GPIO_in...
  • Page 11 GPIO1 connector configuration can be done through system preferences edition with device WebUI or with a script file. GPIO1 configuration part for this script is described here: // Set the direction : input or output (aDirection == "out") Services.prefs.setBoolPref("innes.app-profile.gpio-input.jack35-gpio_1.jack35_1.*.authorized", false); Services.prefs.setBoolPref("innes.app-profile.gpio-output.jack35-gpio_1.jack35_1.*.authorized", true); Services.prefs.setBoolPref("system.connector.jack35_1.1.io.jack35-gpio_1.enabled", true); else if (aDirection == "in")

  • Page 12: Technical Specifications

    Technical specifications Model Manufacturer DMB400 INNES Processors Quad core cortex-A9, 1.2GHz MALI-400 Peripherals 1x USB 2.0 Host (Low/Full/High Speed) 1x USB 3.0 Host (Low/Full/High/Super Speed) 1x Jack 3.5 configurable in GPIO or Infrared 1x RS232 DTE Storage Internal Flash Memory for OS...
  • Page 13 Power supply 12V DC (1.2A) Working temperature Storage temperature 0°C to +40°C -20°C to +60°C Working humidity Storage humidity < 80% < 85% Weight Dimensions (WxHxD) 0,7 kg 191 x 139 x 40 mm...

  • Page 14: Troubleshooting

    Error while playing a media: message "This content <media path/file name> is not compatible with this device" Troubleshooting To solve the issue, remove this not supported media from your playout and publish again. ¹ ¹ For further information, read the document gekkota-supported-medias-and-performances.pdf ² For further information, contact support@innes.pro...

  • Page 15: Conformities

    Conformities In conformity with the following European directives: LVD 2014/35/EU EMC 2014/30/EU...

  • Page 16: Contacts

    Contacts For further information, please contact us at + 33 (0)2 23 20 01 62 or by e-mail: Technical support: support@innes.pro Sales department: sales@innes.pro FAQ and download at : http://www.innes.pro/en/support/ INNES SA 5A rue pierre joseph Colin 35700 RENNES Tel: +33 (0)2 23 20 01 62 Fax: +33 (0)2 23 20 22 59 http://www.innes.pro/fr...