Advertisement
Quick Links
Advertisement
Related Manuals for Innes DMB400W-SSD
Summary of Contents for Innes DMB400W-SSD
- Page 1 User Manual DMB400 4.11.10 001A...
- Page 2 Please read carefully the following instructions before switching the product on: - WARNING! Correct fitting and installation is of the utmost importance. Incorrect fitting and/or installation may result in personal injury or loss. INNES disclaims all liability, of whatever kind, if the product is assembled, fitted and/or installed in an incorrect manner.
- Page 3 Table of Contents Introduction Getting started LEDs Connectors Configuration Web interface Technical specifications Troubleshooting Conformities Contacts...
- Page 4 This device is intended to work with the supplied power supply unit. This power supply unit must be connected to a mains socket conforming to standard NF C 15-100. If the AC power cable is damaged, it must be replaced. It is possible to order a replacement mains unit by sending a request to the email address sales@innes.pro.
- Page 5 Getting started Device front face DMB400 ANT 3 ANT 4 DC IN AUDIO USB2 RS232 DTE HDMI1 OUT Antennas locations Power supply connector Audio connector USB2 3.0 connector RS232 DTE connector HDMI output connector Device front face with the WLAN option DMB400 ANT 3 ANT 4...
- Page 6 200 mm 4,5 mm 7,5 mm Device dimensions DMB400 ANT 3 ANT 4 DC IN AUDIO USB2 RS232 DTE HDMI OUT 200 mm 190 mm Labelling The model of the device, the power supply characteristics, the serial number (PSN) and the MAC address are written on a label which is stuck on the case. Some additional tags may be present in case of built-in options.
- Page 8 Device start-up step > Step 1 (T0=0s) Step 2 (T~23s) Step 3 (T~44s) Device start-up initialisation Device start-up finalisation Nominal mode This phase duration is depending on some variable values During this step, the device has to play the content. (like NTP), some network access duration or some data When firmware upgrade process occured, in checking (check-disk)
- Page 9 LEDs behaviour LED POWER behaviour (power on device) State Information OK: Power supplied Error : Power supply issue ¹ LED LAN behaviour (power on device) State Information There is no network traffic on the Ethernet connector Blinking The blinking frequency is indicating the data rate on Ethernet connector LED STATUS behaviour depending on device start-up steps •...
- Page 10 ¹ If the problem persists in despite of an appropriate power-supply, contact technical support. ² If the problem persists, it is recommended to find out the media not supported yet by the system and remove it from content. ³ If the problem persists after a partition repairing, contact technical support.
- Page 11 Connectors pin-out Power supply connector (12VDC-1.2A) DMB400 DC IN AUDIO LAN connector Ethernet RJ-45. 10/100/1000 BaseT. It is recommended to use shielded cables. Audio Jack 3.5mm connector (stereo L+R) It is recommended to use cables whose length is less than 3 meters. DMB400 AUDIO DC IN...
- Page 12 Video input connector (HDMI 1.4) ANT 2 HDMI IN USB1 Jack 3.5mm connector (GPIO1/IR) ANT 2 USB1 N° Name Write/Read Control Voltage reference 3.3V GPIO1 IN or OUT CPU/GPIO1 Ground Electrical features Vin min Vin max VOH min VOL max VIH min VIL max GPIO1...
- Page 13 (aDirection == "disable") Services.prefs.setBoolPref("system.connector.jack35_1.1.io.uart_1.enabled", true); else //Set Jack 3.5 mode GPIO Services.prefs.setBoolPref("system.connector.jack35_1.1.io.uart_1.enabled", false); // Set the Jack 3.5 direction : input or output (aDirection == "out") Services.prefs.setBoolPref("innes.app-profile.gpio-input.jack35-gpio_1.jack35_1.*.authorized", false); Services.prefs.setBoolPref("innes.app-profile.gpio-output.jack35-gpio_1.jack35_1.*.authorized", true); Services.prefs.setBoolPref("system.connector.jack35_1.1.io.jack35-gpio_1.enabled", true); else if (aDirection == "in") Services.prefs.setBoolPref("innes.app-profile.gpio-input.jack35-gpio_1.jack35_1.*.authorized", true); Services.prefs.setBoolPref("innes.app-profile.gpio-output.jack35-gpio_1.jack35_1.*.authorized", false);...
- Page 14 Device configuration Web interface The device DMB400 supports a configuration Web interface. It is available with the URL: http://<device_IP_addr>/.admin/ The supported Web browsers are : MS-Edge Google Chrome Mozilla Firefox The LAN factory configuration is the mode. DHCP These are the main parameters: Configuration >...
- Page 15 It is recommended to enter a unic for each device used on your locak network. When using several devices DMB400 spread on several buildings or on ⚠ Hostname several locations, it is recommended to enter values having a specific key word reminding the building and the location of the device (for exmaple: Hostname Hall- ).
- Page 16 Technical specifications Model Manufacturer DMB400 INNES Processors Quad core cortex-A9, 1.2GHz MALI-400 Peripherals 1x USB 2.0 Host (Low/Full/High Speed) 1x USB 3.0 Host (Low/Full/High/Super Speed) 1x Jack 3.5 configurable in GPIO or Infrared 1x RS232 DTE Storage Internal Flash Memory for OS...
- Page 17 Power supply 12V DC (1.2A) Working temperature Storage temperature 0°C to +40°C -20°C to +60°C Working humidity Storage humidity < 80% < 85% Weight Dimensions (WxHxD) 0,7 Kg 191 x 139 x 40 mm...
- Page 18 Error while playing a media: message "This content <media path/file name> is not compatible with this device" Troubleshooting To solve the issue, remove this not supported media from your playout and publish again. ¹ ¹ For further information, read the document gekkota-supported-medias-and-performances.pdf ² For further information, contact support@innes.pro...
- Page 19 Conformities In conformity with the following European directives: LVD 2014/35/EU EMC 2014/30/EU...
- Page 20 Contacts For further information, please contact us at + 33 (0)2 23 20 01 62 or by e-mail: Technical support: support@innes.pro Sales department: sales@innes.pro FAQ and download at : http://www.innes.pro/en/support/ INNES SA 5A rue pierre Joseph Colin 35700 RENNES Tel: +33 (0)2 23 20 01 62 Fax: +33 (0)2 23 20 22 59 http://www.innes.pro/fr...
Need help?
Do you have a question about the DMB400W-SSD and is the answer not in the manual?
Questions and answers