Related Manuals for DeWalt DXST4500
Summary of Contents for DeWalt DXST4500
- Page 1 TITAN INDUSTRIAL RACK 4-FOOT TALL / 3-SHELF DXST4500 INSTRUCTION IMPORTANT: Please read this manual carefully before assembling this MANUAL storage rack and save it for reference...
- Page 3 TABLE OF CONTENTS TECHNICAL SPECIFICATIONS SAFETY PARTS LIST ASSEMBLY OPTIONS WARRANTY SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions. Read all instructions and follow them with use of this product.
-
Page 4: Technical Specifications
DXST4500 TECHNICAL SPECIFICATIONS TOTAL CAPACITY 4,500 lb (2,041 kg) *WHEN WEIGHT IS EVENLY DISTRIBUTED CAPACITY PER SHELF 1,500 lb (680 kg) *WHEN WEIGHT IS EVENLY DISTRIBUTED HEIGHT 47” (119.4 cm) WIDTH 49 5/8" (126 cm) DEPTH 18" (45.7 cm) WEIGHT... -
Page 5: Safety
GENERAL SAFETY • Keep work area clean and dry. • Use correct/recommended tools for the job. • Never leave unattended tools plugged in or running. • Never force a part into place. • Wear appropriate safety apparel for the job you are doing. •... -
Page 6: Table Of Contents
DXST4500 No. Description No. Description Qty. Qty. Vertical Beam Laminate Deck Pre-Bolted Vertical Assembly 10 mm Nut Vertical Assembly Bolt Locking Shelf Pin Carriage Bolt Stacking Plate 10 mm Wrench Crossbeam 4 mm Hex Key Shelf Support Strap 4 mm Hex Bit... -
Page 7: Assembly
Tools Required for Rack Assembly: 4 mm Hex Key (included) OR 4 mm Hex Bit (included); Rubber Mallet (not included) -
Page 8: Vertical Beam
DXST4500 EXPANDABLE UPRIGHT FRAME INSTRUCTIONS • Note: For ease of assembly, two (2) Vertical Beams feature pre-bolted horizontal and diagonal beams, as well as 2 ft 18" pre-attached U-Bracket Covers. (61 cm) (45.7 CM) STEP 1 • Place one (1) Vertical Beam and one (1) Pre-Bolted Vertical Beam on the floor, parallel to one another (about 18”/45.7 cm... - Page 9 Make sure the crossbeams are attached at the same level on both sides. If you plan to stack another DXST4500 Industrial Rack on top, then DO NOT attach the third set of crossbeams to the very top of the upright frames.
- Page 10 DXST4500 SHELF SUPPORT AND SAFETY STRAP INSTRUCTIONS • Note: There are two (2) Safety Straps with Weld Nuts and three (3) Shelf Support Straps for every set of crossbeams. STEP 1 • Starting with the lowest set of crossbeams, place a Safety Strap with Weld Nut between the lower ridges of the crossbeams where two sets of holes have been pre-drilled.
-
Page 11: Carriage Bolt
WALL MOUNTING INSTRUCTIONS • Note: Drywall anchors and anchor screws are included with this rack; however, different wall materials require different types of fasteners. Use fasteners suitable for your specific type of wall. If you are uncertain about what type of fasteners to use, then please contact your local hardware store. -
Page 12: Crossbeam
DXST4500 LAMINATE DECK AND LOCKING SHELF PIN INSTRUCTIONS STEP 1 • Place the first laminate deck onto the top ridge of the crossbeams. If seated properly, it will “pop” into place and lay evenly. Repeat for the remaining decks. STEP 2 •... -
Page 13: Locking Shelf Pin
STACKING INSTRUCTIONS Note: Every DXST4500 Industrial Rack comes with two (2) TOP RACK stacking plates. In order to safely stack two of these racks together, you MUST use four (4) of these plates. It is recommended that one person holds the upright frames in place while a second person installs the stacking plates. - Page 14 DXST4500 MAXIMIZE YOUR DEWALT STORAGE OPTIONS NOTE: Connect multiple racks together to increase both length and height. * Additional racks are sold separately.
- Page 15 ONE YEAR LIMITED WARRANTY DEWALT will replace this industrial rack due to faulty materials or workmanship for one year from the date of purchase (be sure to keep your receipt). This warranty does not cover part failure due to normal wear or rack abuse. This warranty does not apply to accessories or damage caused where repairs have been made or attempted.