Contents 1. Specifications: 2. Features: 3. Charger’s exterior appearance 4. Warning and security tips 5. Program flow chart 6. How to set charge current 7. Lilo/LiPo/LiFe/LiHv battery program 8. NiMH/NiCd battery program 9. Pb battery program 10. Cell meter test program 11.
1.Specifications: Input Voltage DC.10-18V 0.1-6A Charge Current Discharge Current 0.1-2A Charge Power max.50W max.5W Discharge Power Balance Current max.200mA Balance Tolerance ±0.01V LiXX:1-16cells Charging Capabililty NiXX:1-6series 2-20V Pb Battery Voltage Discharge Battery 3.0-4.2V/cell Weight Dimensions...
2. Features: Advanced Operate software The charger can set current automatically when charging/discharging. Especially for the Li-xx battery, it can avoid the explosion due to the wrong operation by user. All of them can set according to the user’s choice. The charger provide balance port for Li-xx battery, including 2, 3 ,4,5,6-cell five balance port.
Page 5
external temperature sensing line). Charge time Limit: It can prevent over charge and discharge by setting a charge time. Input current checking: In order to protect the battery it can check the voltage of the battery during charging process. The charger will turn off charge current with an alarm automatically when the voltage decreased to the lowest.
4. Warning and security tips Never leave the charger unsupervised when charging, if any mal-function is observed please terminate the process immediately and refer to the manual. •Never put the charger into the place which dust/damp/vibrate. •The input power is only for DC 10-18V. •Please put it onto the surface which it is firm/Anti flammable.
Page 8
Voltage grade: 1.2v/cell llowed fast charge current: 1C~2C rely on the running of the battery. NiCd/NiMH Discharger voltage cut off grade: 0.85v/cell (Nicd battery) 1.0v/cell (Nimh battery) Voltage grade: 3.6V/c Max charge voltage: 4.1V/cell Lilo Allowed fast charge current: 1C or less Min discharge voltage cut off grade: 2.5V/cell or More Voltage grade: 3.7V/cell Max charge voltage: 4.2V/cell...
Page 9
Discharge •The discharge parameter should be set according to the rest of battery capacity or decreased battery voltage. When discharging, it should be pay more attention to the discharge process. It must set the correct discharge voltage, in order to avoid the over discharging.
5、Program flow chart Start STATUS STATUS STATUS STATUS BATT/PROGRAM Enter LiXX CHARGE LiXX BALANCE LiXX FAST CHG LiXX STORAGE LiXX DISCHARGE LiXX BATT Batt type STATUS STATUS STATUS STATUS Stop STATUS Start BATT/PROGRAM STATUS STATUS STATUS STATUS Enter NiXX CHARGE NiXX Auto NiXX DISCHARGE NiXX RE-REAK...
Page 11
The relationship between the C value and the charging time: charging time≥ 60min/charging c value(for example, it need 60-70 minutes to complete 1C charging ).Due to battery differences in energy efficiency conversion, this time may be extended. 7. Lithium battery(Lilo/LiPo/LiFe/LiHV)program Use these programs only when charging a lithium battery ( Lilo/LiPo/LiHV/LiFe) with a nominal voltage of 3.6V, 3.7V, 3.8V or 3.3V per cell, respectively.
Page 12
This shows the number of cells you set up and the processor detects. ' R: ' shows the number of cells found by the charger and ' S:' is the number of cells selected by you at the previous screen. If both numbers are identical you can start charging by press Start/Enter button.
Page 13
7.3 'FAST' charging Lithium battery The charging current is getting smaller as the process goes to the near end term of Lithium battery chaging. To finish charging process earlier, this program eliminate certain term of CV process. Actually, the charging current will goes to 1/5 from the initial value to end the process while the normal chaging goes to 1/10 during CV term.
Page 14
7.5 Discharging Lithium battery The value of discharge current on the left side of screen may not exceed 1C for a maximum safety and the final voltage on the right should not be under the voltage level that is recommended by the battery manufacturer to avoid deep discharging.
8. NiMH/NiCd battery program These programs are for charging or discharging NiMH (Nickel-Metal-Hydride) or NiCd (Nickel-Cadmium) battery commonly used for R/C model aplications. To alter the value at the display, press Start/Enter key to make it blink then change the value using INC or DEC key.The value will be stored by pressing Start/Enter key once.
Page 16
8.3 Charge-to-discharge & discharge-to-charge cycle NiMH/NiCd battery Set the sequence on the left and the number of cycle on the right. You can use this function for balancing, refreshing and break-in the battery. To avoid rising temperture of the battery, there will a brief cool-off period that already fixed at 'User setting' after each charge and discharge process.
Page 17
9. Pb( lead-sulphuric acid) battery program This is programmed for charging Pb( lead-sulphuric acid) battery with nominal voltage from 2 to 20V. Pb batteries are totally different from NiCd or NiMH batteries. They can only deliver relatievely lower current compare to their capacity, and similar restrictions definitely apply to charge.
10、Cell meter test This charger also can be used as a cell meter. It can BATT/PROGRAM show the average voltage and the highest/lowest BATT METER voltage of each cells. Batt type Start Stop Enter Choose the cell meter program interface, press Start to 4.16 4.18 4.17 V...
Page 19
12、Memory Mode B6 Charger can save setting data of each programs, it can save 10 groups data for each kind of battery, including the cells of the battery, setting charge current and so on. Users do not need to set the data again when they use the batteries which have been memory. Easy and convenient to use.
13、User settings In the open state, when the charger starts to work, the Safety Timer safety timer automatically starts the timer at the same 240min time. If the system is wrong or the system can't check the battery capacity is full, this setting can prevent the battery from overcharging.
Page 21
The automatic charging trigger voltage is an automatic NiCd Sensitivity charging current closing program. The principle is that D.Peak Default when the battery voltage rises to the highest point and starts to back down, it closes the charging current automatically to complete the charge process. If the trigger voltage is set too high, easy to cause overcharging.
14、Warning and Error information It will show the Error information with an alarm when use the wrong operation. 1.{" REVERSE POLARITY "} Battery output Polarity connection wrong; 2.{" CONNECTION BREAK "} Interruption between battery and output end, or the charger wire was not been connected well when charging/discharging.
15、Warranty and service We warrant this product for a period of one year(12 months) from the date of purchase. The guarantee applies only to such material or operational defects, which are present at the time of purchasing the product. During that period, we will replace without service charge any product deemed defective due to those causes.
Need help?
Do you have a question about the Accucell-6 and is the answer not in the manual?
Questions and answers