Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for swepac F 80A
Summary of Contents for swepac F 80A
- Page 1 F 80A USER MANUAL IN ORIGINAL Doc: 101516-GB 1810...
-
Page 2: Table Of Contents
F 80A SWEPAC F 80A used to pack freshly laid asphalt on pavements and garage approaches, in connection with roadworks, etc. The machine is designed to pack small asphalt areas and is particularly suitable for additional works and repair works. The compact design with an articulated control handle makes the machine very easy to manoeuvre. -
Page 3: Standards
F 80A STANDARDS Noise Measurement in accordance with the standard EN 500- 4 Rev. 1:1998, Annex C: Measurement uncertainty ± 0.5 dB (A) in 95% of the measurements. In accordance with the conditions in Directive 2000/14/ EC, Annex VI, the following values are reported: F 80A Sound pressure levelat the operator’s... -
Page 4: Signs
F 80A SIGNS Warning signs Machine Signs MACHINERY Before use, carefully read the manual and its safety instruc- tions so that you can handle the machine safely. Ensure that the manual is always accessible. 1. Manufacturer 2. Place, country of manufacture. -
Page 5: Technical Data
F 80A TECHNICAL DATA FUNCTION The machine consists of a base plate with a vibration element F 80A and an upper part cushioned from the base plate. The upper part include even carrying handle. The lifting eye Net weight .........80 kg include even an water tank bracket. -
Page 6: Technical Description
F 80A TECHNICAL DESCRIPTION 1. Handle 2. Protective cover 3. Petrol engine 4. Engine plate 5. Centrifugal clutch 6. V-belt 7. Rubber damper 8. Vibration element / Base plate 9. Water tank 10. Lifting eye / Water tank bracket... -
Page 7: Daily Checks
F 80A DAILY CHECKS V-belt Drive Check the tension and condition of the V-belt regularly. Fuel Check Check that there is fuel in the tank. Top up if necessary. Engine Oil Level Check Check the oil level in the crankcase every day. The oil must reach the edge of the filling hole when the machine is on a level surface. -
Page 8: Before Starting The Engine
F 80A Oil level Engine power switch Active Not active Full RPM Idle Choke Fuel cock Throttle lever BEFORE STARTING THE ENGINE AFTER STARTING See Daily Checks on page 8. Switch the throttle lever to idle. Open the choke gradually. -
Page 9: Water Tank
F 80A MOUNT THE WATER TANK The water tank for the F 80A is removable. To mount the water tank do this steps: Push the water tank down with the side lock open. The rear part of the water pos. 1 tank´s should be placed in the holder on the bracket. -
Page 10: Transportations
F 80A TRANSPORTATION Transport locking It is easy to remove the handle without tools, and the boot Secure the machine with straps according to illustration of a standard car is sufficient to transport the machine. during transportation Note! Secure it by the base plate and not the rubber- Lifting by hand cushioned upper part. - Page 11 F 80A NOTES...
- Page 12 F 80A NOTES...
- Page 13 F 80A NOTES...
-
Page 14: Notes
F 80A NOTES... -
Page 15: Ec-Declaration Of Conformity
The product complies with the following directives: 2006 / 42 / EG 2000 / 14 /EG 2004 / 108 / EG EN 500-1 EN 500-4 Technical documentation held by: Swepac AB, Blockvägen 3 SE-34132 Ljungby Tomas Johansson / Product Engineer... - Page 16 SWEPAC AB Address Blockvägen 3, 341 32 Ljungby, Sweden, tel. +46 (0)372-156 00, fax +46 (0)372-837 41, E-mail mail@swepac.se, Internet www.swepac.se...
Need help?
Do you have a question about the F 80A and is the answer not in the manual?
Questions and answers