Soyal AR-331 Manual

Soyal AR-331 Manual

Access controller, touch-panel metal housing/illuminated touch-panel

Advertisement

SOYAL
ACCESS CONTROL SYSTEM
Contents
AR-321 (H): Touch-panel Metal Housing
1
2
Product
AR-331 (H): Touch-panel Metal Housing / AR-331 (H-S): Metal Housing
1
Product
or
WG keyboard
AR-331 (H)
AR-331 (H-S)
AR-721 (H)
1
Product
AR-725 (H): Illuminated Touch-panel
AR-725 (H-M)
1
Products
A.
B.
AR-725 (H)
1
Products
A1.
E.
AR-725 (X)
1
Products
A2.
A3.
AR-757 (H)
1
Product
Parts Description
a.
Button Head Pozidriv
Tapping Screw: M3x10
e.
Security Torx Screw:
M3.5x15
AR-321 (H) / AR-331 (H) /
®
AR-721(H) / AR-725 (H) / AR-757 (H)
3
User Guide
Terminal Cables
P1
2
Optional
[Optional]
AR-721RB
Digital Relay
or
AR-821RB
Original Relay
2
User Guide
C.
D.
F.
B.
C.
G.
2
User Guide
b.
Button Head Pozidriv
Slotting Screw: 2.5x10
f.
Flat Head Hex Socket
Screw: M3x8
4
P2
P3
P4
3
User Guide
3
Terminal Cables
P1
P2
2
User Guide
2
User Guide
H.
D.
3
Terminal Cables
P1
P2
c.
Flat Head Cap Philips
Tapping Screw: 4x19.1
g.
Security Torx Screw: M3x10
Tools
d x2
※ Additional external relay must be purchased.
4
Terminal Cables
5
Tools
P7
P3
P4
3
Terminal Cables
P1
P2
P3
P4
3
Terminal Cables
P1
P2
P3
P4
2
Tools
a x2
b x2
c x2
P3
P4
P6
d.
Flat Head Cap Philips
Tapping Screw: 4x38
h.
Security Torx Wrenches
V140707
5
Water proof Strip
c x2
g x1
h x1
4
Tools
f x2
4
Tools
c x2
e x1
4
Tools
f x2
e x1
4
Tools
f x2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AR-331 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Soyal AR-331

  • Page 1 AR-321 (H): Touch-panel Metal Housing Product User Guide Terminal Cables Tools Water proof Strip d x2 AR-331 (H): Touch-panel Metal Housing / AR-331 (H-S): Metal Housing ※ Additional external relay must be purchased. Product Optional User Guide Terminal Cables Tools...
  • Page 2: Installation

    Use the Allen key and screws (accessories supplied) to assemble the body onto the mounting plate. Turn on the power, and LED will light and beep will sound. AR-331 (H) / AR-331 (H-S) Remove the rubber plug. To cut tamper-resistant column and make it fit the appropriate height for actual installation.
  • Page 3: Connector Table

    AR-321 (H) / AR-331 (H) / SOYAL ® AR-721(H) / AR-725 (H) / AR-757 (H) V140707 ACCESS CONTROL SYSTEM Notice 1.Tubing: The communication wires and power line should NOT be bound in the same conduit or tubing. 2.Wire selection: Use AWG 22-24 Shielded Twist Pair to avoid star wiring.
  • Page 4: Wiring Diagram

    ※ 1.Enable the security trigger signal: Please refer to the 34 2.Disable "Exit by RTE Button". (Please refer to the of function default value.) Connect to Access Control for Connect to arming tools for Door Contact AR-331 (H) AR-331 (H) POWER Alarm 12VDC N.C.
  • Page 5 12VDC External WG keyboard ※ If you want to program system on AR-331 (H-S) directly, please order WG keyboard then install it according to the following pattern. Remove the Protection plug that at the right bottom. (※ Do not lose protection plug or it will affect the protection level.) WG Keyboard cable will be connected to the pin board.
  • Page 6: Operation Process

    Access Controller Touch-panel Metal Housing / Illuminated Touch-panel V140707 Operation process A. Enter / Exit Program Mode Enter the program mode Input 123456 PPPPPP [e.g.] The Default Value= 123456, if the Master Code is already changed= 876112, input 876112 → program mode entered Master Code modification Exit the program mode Enter program mode →...
  • Page 7: Function Default Value

    Enable: Enter program mode → Disable: Enter program mode → ※ [The normal procedure to open door] can refer to [Access Mode]. Function Default Value AR-321 (H) / AR-331 (H) / AR-721 (H) / AR-725 (H) / AR-757 (H) ※Default Value Function Selection...
  • Page 8: Command List

    Access Controller Touch-panel Metal Housing / Illuminated Touch-panel V140707 Command List Description Function Command Mode PPPPPP Enter program mode PPPPPP=Master Code, default value=123456 M4/M6/M8 Exit program mode M4//M6M8 Exit program mode and enter arming mode M4/M8 Node ID setting (Connected to 716E) NNN=Node ID of Access Controller (range: 001~016) M4/M8 Node ID setting (Connected to the PC directly...

Table of Contents