Planet DSP-1000 User Manual

BASIC INFORMATION OF DSP-1000
B. Default Zone Definitions
Your DSP-1000 will follow the CF storage files to play the contents. By default it is single zone, you
v
could change to three or four zones and DSP-1000 basically will follow the settings to play them.
4-Zone Display
AVI - motion file area
u
The motion file is located at root directory. And this file can manually replaced by editing the file
"play.lst". The current file name used in this demo is "UMG2000.avi" in size 540 x 360 pixels at 30fps.
w u
Title banner
v
The file is located at "\toppic" folder with the format JPEG (".jpg" file). The current file name used in
this demo is "DSP.jpg" you can just replace this file to change your title banner.
w Advertise picture area
Those files are located at "\pic" folder. You can just replace those files to change your advertise files.
x
However, for the timing setting, please install the "Config Tool" for more. The Config Tool can be
found in the CD-ROM.
x Scrolling Message
For the scrolling message, you are required to use the Config Tool to change the scrolling text and the scrolling speed.
C. File Structure of Demo Folder
u \pic: Advertise picture folder. DSP-1000 will play all the files in this directory continuously. The
default image size is 180 x 420 pixels with JPEG format. And it is also suggested to use Config
Tool for the change timing of the pictures.
v \toppic: Title banner image folder. The Title banner image default size is 540 x 60 pixels with JPEG
format
w Play.lst: A text file that have the basic define of the files to play and play related settings. For the
first installation, please just keep the format. And later you can use Config Tool for more settings.
Please refer to the user manual for more.
D. DSP-1000 Start up sequence
2. Set up Display Environment base
1. Power On
on the system configuration
1. Please make sure all the connections are well connected.
2. If the screen did not shows up the boot up screen please use the Remote Controller to check the TV mode.
3. Make sure the Play List is with correct file name according to the files in the storage.
4. If the played contents did not match the screen, please double check the image size of your files.
5. For Background Updates, please refer to the User Manual for more.
E. Config Tool installation
In the CD-ROM, there is also the Config Tool utility, this utility will also help you to:
1. Setup the play list
2. Setup the scrolling message
3. Setup the picture rotation speed
4. And more advanced setup including
4.1. System setup like IP address, Screen setup, etc..
4.2. Zone division setup such as video screen on right or left.
4.3. Content Update setup such as interval, server location, type of download
Please also install this Config Tool utility into your management PC for advance
management of your installed DSP-1000 or DSP-1000W in your Local Area
Network.
Quick Guide
PLANET Technology Corporation
11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C.
Tel: 886-2-2219-9518 Fax: 886-2-2219-9528
Email: sales@planet.com.tw www.planet.com.tw
2011-K20040-000
u
v
w
3. Check the Play List 4. Play the contents 5. Background check the
file (Play.lst) accordingly Update Server
PLANET reserves the right to change speci cations without prior notice. All brand names and trademarks are property of
their respective owners. Copyright © 2010 PLANET Technology Corp. All rights reserved.
VERIFY THE CONTENTS INSIDE PACKAGE BOX
The package box should contain the items indicated below plus DSP-1000 / DSP-1000W.
If any item is missed or damaged, please contact the seller immediately
User's Manual Quick Installation Guide CD-ROM
Adapter Ethernet Cable S-Video / RCA AV Cable
INSTALLATION REQUIREMENT
A. Storage Device B. TV
128MB (at least)
2GB (or above suggested)
TV set with RCA interface
or
2.5" SATA HDD
Note: In this guide we use CF
card for the first quick
TV-set with HDMI interface
installation. If you would like
to use HDD, pleaes refer to
user's manual for more Note: In this guide we use RCA TV set as the setup example
DSP-1000
DSP-1000W
YPbPr AV cable Antanna Remote Control
(DSP-1000W)
x 6
x 1
VGA AV Cable Bracket Package
C. PC
PC with
1. CD-ROM
2. CF Card Reader
3. LAN interface
or
Note: In this guide we require the PC
to copy the contents to the CF
Card for the first installation
D. Network Switch (option)
Network Switch
x 2