LUXOMAT PD9-M-1C-SDB-IP65 Installation And Operating Instruction Manual

LUXOMAT
B.E.G.
Installation and Operating Instruction for
1. Mounting preparations
Work on the 230 V mains supply
may only be carried out by qualified
professionals or by instructed persons
under the direction and supervision of
qualified skilled electrical personnel
in accordance with electrotechnical
regulations.
Disconnect supply before installing!
When in Master/ Slave mode of
operation, the Master-appliance
must always be installed at the
location where there is least
daylight.
4. Option:
IR-PD9
Wall bracket for remote control
IR-PD9
IR-PD-Mini
7. Exclude sources of
interference
In case the sensing area of the
LUXOMAT PD9-M-1C-IP65(-GH) is too
®
large or areas are being covered that
should not be monitored, the range
can be reduced or limited through use
of the enclosed masking clips.
®
B.E.G. -
2a. Installation
The detector has
min. 32 mm
22 - 30 mm
been designed and
developed specifically
for installation in
suspended ceilings.
A circular opening of
diameter min. 32 mm
must be produced in
the ceiling.
Having connected the cables in accordance with
the regulations, connect the power supply via the
RJ11 plug. Therefore, open the power supply with
the help of the screws and close it afterwards. After
that, put the power supply through the opening in
the ceiling and mount the sensor onto the ceiling
according to figure.
5. Settings by remote control
or
Resetting when
open:
Deletes all values
or
set with the
remote control,
light OFF.
to
20
+
15
to
sec
HA
or
ON
t < 5 sec.
8. Range of Coverage
PD9-M-1C-SDB-IP65
RJ
2.50 m
3
2
1
PD9-M-1C/S-SDB-IP65(-GH)
PD9-Master-1C/-Slave-SDB-IP65(-GH)-FC
Occupancy detectors
2b. Connecting
terminals
N
N
L
L
Unlocking device - Activation
of the programming mode
Daytime operation, detector only
activated by motion
Automatic reading in the current light
value as new luminance set point
Luminance set point for channel 1
1000
20 - 1000 Lux
max
Increase the current light level by
20 resp. 50 Lux
ON
Follow-up time (relay and channel 1)
30
min 15 sec. - 30 min.
OFF
Change between fully automatic
HA
and semi automatic mode (HA)
OFF
Light ON/OFF
Locking device - Exit programming
mode
red LED flashes
Permanent protection against
sabotage
PD9-M-1C-SDB-IP65-GH
RJ
10.00 m 6.00 m
1 quer zum Melder gehen Walking across
2
frontal zum Melder gehen Walking towards
3 Seated
Unterkriechschutz
2c. Self test cycle 3. Settings carried out
using remote control
(optional)
200
400
600
Remote control
LUXOMAT
10
12
The LUXOMAT PD9-M-1C- Check Battery:
®
15
IP65(-GH) enters an initial Open battery compartment
60-second self-test cycle, by pressing the plastic springs
when the supply is first together and removing the
connected. The occupancy battery-holder.
detector is ready for operation.
6. Key functions in closed state
Permanent protection against sabotage
This function blocks the unit permanently (green LED is
illuminated). This operating mode can only be activated
t < 5 sec.
during the period of 5 seconds after pressing the "lock"
button. This status will only permit actuating the function
"Light on/Light off".
The procedure for leaving this mode is as follows:
1. Switch off the current
2. Apply current for 31 – 59 seconds
3. Switch of the current again
50
1500
Lux Lux
4. Apply current
5. Open detector
Light on/off when closed
=> (see page 2, point 11)
The light will remain switched on/ off for as long as
movements are detected in the areas of coverage.
Once the last movement has been detected, the light
will remain on for the duration of the follow-up time as
per setting.
The appliance will then return independently to the
mode selected (Fully or Semi-automatic).
Activation/Deactivation of the test function
Switches channel off and is immediately active again,
exits all timers, interruption of light measurement
Confirmation
Changes to „open" state
9. Dimensions
PD9-M-1C-SDB-IP65 PD9-M-1C-SDB-IP65-GH
25 25
45
45
154 mm
100
200
N
400 PD9-SDB-
600 MASTER-
N
SENSORHEAD
1000
1500
Lux
2 1
6 4
PD9-SDB-
8 TEST
L SLAVE-
10
12
SENSORHEAD
L 15
20
25 30 mins
GB
100
PD9-SDB-
MASTER-
SENSORHEAD
1000
1500
Lux
2 1
4
6
PD9-SDB-
IR-PD9
® TEST
8
SLAVE-
SENSORHEAD
20
25 30
mins
25 mm
38 mm