Advertisement
Quick Links
TINA
PORTABLE CRIB
ORBELLE'S ORIGINAL DESIGN
ASSEMBLY INSTRUCTIONS
Read all instructions before
Attention: In order to properly assemble
assembling crib.
the crib, follow the assembly instructions
Save instructions for future use.
in the specified order.
Failure to assemble the crib in the
manner recommended could make the
Carefully remove and lay out all parts.
crib hazardous.
Familiarize yourself with all diagrams to
facilitate the assembly of your crib.
Warning:Never use this product if there
Check parts and the enclosed hardware
are any loose or missing fasteners,
bag with the hardware parts list to be
loose joints,broken parts, or torn
sure all are included and quantities
mesh/fabric. check before assembly and
are correct.
periodically during use. Contact
Destroy cardboard and plastic bags
ORBELLE. for replacement parts and
immediately.
instructional literature if needed.
.
This product meets or exceeds specifications as issued by the consumer product safety for non-full size baby cribs.
.
Caution:Before using this unit recheck all screws to be sure they are tightened securely. a periodic check should be made of
all screws&nuts to be sure they remain tight.
.
In gaps between a mattress too small or too thick and product sides.
.
On soft bedding never add a mattress, pillow,comforter,or padding.
.
Use up and middle level mattress support only for a new born baby and not more than the first 3 months.
.
Failure to follow these warnings and the instructions could result in serious injury or death.
.
Do not use plastic shipping bag or other plastic film as mattress covers not sold and intended for that purpose, they can
cause suffocation.
.
Never use a watter mattress with this product, if refinishing,use anontoxic finish specified for children's products.
.
Strings can cause strangulation! Never place items with a string around a child's neck,such as hood strings or pacifier cords.
Never suspend strings over product or attach strings to toys.
.
Discontinue use of the product when child is able to climb out or reaches the height of 35in.(890mm).
.
When child is able to pull to standing position,set mattress/base to lowest adjustment position and remove bumper pads,
large toys ,and other objects that could serve as steps for climbing out.
.
Never place product near window where cords from blinds or drapes can strangle a child.
.
Always provide the supervision for continued safety of your child.
.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless otherwise
advised by your physician.
.
Never use this product if there are any loose or missing fasteners, loose joints,broken parts, or torn mesh/fabric. check before
assembly and periodically during use. Contact ORBELLE. for replacement parts and instructional literature if needed.
.
Never substitute parts, the product including side rails, must be fully erected prior to use.
PARTS LIST FOR #TINA
B
A
A:
Left head board (1PC)
B:
Right head board (1PC)
F:
Stabilizer bar (1PC)
E:
Mattress board (1PC)
a:
b:
3" Allen head bolt (10 pcs)
Barrel nuts (10 pcs)
d:
1-1/2" Wood dowel (2 pcs)
WARNING
****Keep instructions for futher use****
WARNING
****Infants can suffocate****
WARNING
MADE IN CHINA
CAUTION:
Any mattress used in this crib must be at least 23-5/8"(600mm) by
37-3/4"(959mm) with a thickness not exceeding 2"(51mm). This crib conforms
to applicable regulations promulgated by the consumer product safety
commission.
C:
Front rail (1PC)
D:
Back rail (1PC)
A
G:
Mattress (1PC)
STEP 1
Make sure that the latch on the bottom of each
headboard ( A & B ) are locked.
c:
2" Allen wrench (1 pc)
D
e:
Castors (4 pcs)
A
b
a
E
c
d
a
b
a
STEP 3
Assemble stabilizer bar (F) to the headboard ( A & B )
by sccrews(a) and nuts (b) and wood dowels(d).
Connect front rail ( C) to the headboard ( A & B)
according to step 2.
D
E
A
C
e
e
STEP 5
Assemble casters (e) to the leg bottoms
on the leg on headboard (A & B).
B
a
c
a
STEP 2
Connect back rail ( D) to the headboard ( A & B) by
screws (a) and nuts (b).
a
B
a a
C
d
b
STEP 4
Put the mattress support (E) in the double plastic holder
on the headboard according to your required height ,
and lay it down, then add the mattress (G).
Warning: please put the mattress support on
the up and middle height only for newborn baby.
B
E
e
STEP 6
Follow bellow to fold the crib:
1.take out the mattress (G)
2.take out the mattress board (E)
3.unlock the latch on the headboard
4.fold the crib
a
b
B
D
b
A
b
B
D
E
C
A
Advertisement
