Windguard Adjustment; Pro Speed; Windrowing; Evenbaling - Welger AP 42 Operating Manual

Table of Contents

Advertisement

Windguard Adjusfmenf
The windguard
can be set info two different positions, freely movable between
two stops. Accordingly
to different
info a lower or higher position. T0 pick-up short material the windguard is fixed
'4:
intb ,tower hole po
sition of pick-up side guard. Normal baling material in higher
.
hole position of pick-up side guard.
, Seffing fhe Bale Lengfh
By turning adjusting nut 4 (page 6, fig. 9) in direction of arrow the bole is getting
Ionger, turning in opposi.te direction the bole is getting shorter.

pro Speed

To maintain the specified number of rem strokes of 100/min. your pro
must be 540 r.p.m. Check this against your watch from time to time. Fast running
-
may causa trouble end wear
universal joint.

Windrowing

The machine's capacity can only be lJ.tilized to the full when the crop is carefully
raked info' windrows. The windrow should be about 1.60 m wide.

EvenBaling

end close matching of tractor speed to windrow height are very important. Where
windrows
are tigntly bunched, briefly stop the tractor
clear itself.

Before Turning

Before turning sharp curves disengage pro

Safety Devices

Indicating end teil lights must be kept clean end. shou,ld not be covered by over-
hanging material. Check function of lighting system regular. Two chocks should
always be carried on the baler.
Useful
Deflecfor Chufe
throws the boles to the left or right for more clearance of tractor with baler
attached (part number 1115.81.91.01). Fit deflector chute underneath bole chute
end secure with hooks.
Special Tyres
Special Irres are availbale if needed for special purpose.
1121.02.10.00
Order number
for AP
left end 7.00-12 Impl. 2 bar for the ride side. Necessary for operation with P 23.
Order number 1122.02.10.00for AP 48/53 comprising of one Irre
2 bar for the-Ieft side end 8.00-12Impl. 1.5 bar for the right side.
8
baling material, the windguard
can be set
slow running overloads drive components end
end allow the baler to
to prevent damage to drive parts.
Accessories
38/42
with ~yres 10.0/75-15Impl. 2.3 bar for the
11.5/80-15
Bale Wedges
narrow
baling chamber cross section end so increase bole density. They should
only be fitted
1115.03.90.00.
Drawbar Eye for 20 mm (/) Pin
Thi5
type of drawbar
2101.05.07.00) has been
small tractors.
Pick-up Cover Sheef
Pick-up cover sheet i5 recommended for pic~ing up short-stalk crops. (Order
1705.42.92.00
number
speed
Wide-Angle
Universal Shaft
Tractor with attached baler becomes more manoeuvrable,
joint can deflect up to 70 degrees end needs no disengaging when negotiating
curves (order number
Universal Drive Shaft wifh Overrunning Clufch
It is advisable to use drive shaft with overrunning clutch on tractor's with hydraulic
opemted pro.
sllaft with overrunning
sIlan with overrunning clutch order number
Trailer
Hifch
Trailer hitch for AP
number 1122.89.01.00) adjustable
loading chute or the baler mounted bole thrower
Fit support pipe underneath
pipe in required position end
Mounti.ng:
AP 38/42
fhe boJe chamber end i5 locked info required position with pin end spning
~
Attention! It is not allowed to have more thon
lights villen trave,lIing on open roads.
Deflecfor Chufe
throws the boles to the left or right for more clearance of tractor with baler
attached (part number 1105.81.90.00).
Assembly: by
shaft,
Loading Chute
Loading chute (order number
1105.81.06.00)fitted with trailer hitch, pushes
Attenfion: Bale chute mu~t be laken off the baler for road transport.
Foldable Loading Chufe
A
foldable
loading
1122.80.00.00).
The chute remains on the baler during transport, it is only folded
to the front. For AP 38/42
Impl.
~
when
handling
dry crops, optional
2 or 4 pe. Order number
eye (order number
1105.05.90.00)
designed to f.it the baler more easily to the drawbar of
38/48, for AP 42/53 order
for AP
number
-
0930.14.03.00).
If fitted, overrunning dutch shou'ld be fitted on baler side. Drive
0930.10.13.00i
clutch, order number
0930.14.04.00.
38/42
1121.81.01.00) end for AP 48/53
(order number
for
length
is -necessary
P 23.
of ba,le chamber. Insert trailer h,itch ,info support
with pin end
spr,ing clip.
secure
the trai,ler hitch ,is
pushed ,info the pipe
1000
safety spring
end chain at the chamber outtet.
for AP 38/42: 1104.81.06.00 end for AP 48/53:
the boles on to an attached trailer.
is also available
for AP 48/53
chute
order number 1121.80.00.00.
/
with pin (part number
1121.42.92.00).
as the wide-angle
wide angle drive
(order
when working
with
which is welded under
clip.
mm overhang behind teil
(order
number
9

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Ap 38Ap 53dAp 48Ap 53Ap 48d

Table of Contents