Related Manuals for A-Neuvideo ANI-2PIP-LOGO
Summary of Contents for A-Neuvideo ANI-2PIP-LOGO
- Page 1 ANI-2PIP-LOGO 2x1 HDMI Multiviewer A-NeuVideo.com Frisco, Texas 75034 (469) 277-7606 AUDIO / VIDEO MANUFACTURER...
- Page 2 SAFETY INFORMATION To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. Follow all instructions printed on unit chassis for proper operation. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. Make sure power outlets conform to the power requirements listed on the back of the unit.
-
Page 3: Table Of Contents
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. The ANI-2PIP-LOGO HDMI Multiviewer is capable of scaling up • To protect the unit from overheating, do not block any vents or... -
Page 4: Features
NEUVIDEO FEATURES FEATURES • HDMI & HDCP 1.3 compliant • (2) HDMI inputs and (1) HDMI output • Inputs and output support HD resolutions up to 1080p@60Hz and PC resolutions up to WUXGA (RB) • Supports audio pass-through of LPCM 2.0/5.1/7.1 sources via HDMI •... -
Page 5: Specifications
NEUVIDEO SPECIFICATIONS Specifications • HDMI Bandwidth: 225MHz/6.75Gbps • Input Ports: (2) HDMI • Output Ports: (1) HDMI / (1) Stereo (Terminal Block) • Control Interfaces: • (8) Trigger (Terminal Block) • RS-232 (9-pin D-sub) • IP Control (RJ-45) • Baud Rate: Up to 115200bps •... -
Page 6: Operation Controls & Functions
NEUVIDEO Operation controls & Functions Front Panel SERVICE: This port is reserved for firmware update use only. POWER LED: This LED will illuminate to indicate the unit is on and receiving power. SWITCH BUTTON: Press to toggle between the two HDMI inputs and output the selected source full screen. NOTE: Press and hold this button for 2 seconds to change the output resolution to 1920x1080p@60Hz. -
Page 7: Rs-232 Pin Definition / Telnet Control
NEUVIDEO RS-232 Pin Definition / Telnet Control RS-232 Pin Definition ASSIGNMENT ASSIGNMENT Baud Rate: 110 ~ 921600 Data Bit: 8 bits Parity: None Stop Bit: 1 bit Flow Control: None Telnet Control Before attempting to use Telnet control, please ensure that both the unit and the PC are connected to the same active networks. O ACCESS THE COMMAND LINE INTERFACE (CLI) Windows 7 Click START, type “cmd”... -
Page 8: Rs-232 & Telnet Commands
NEUVIDEO RS-232 & Telnet Commands RS-232 & Telnet Commands COMMAND DESCRIPTION & PARAMETERS DESCRIPTION & PARAMETERS Show the full command list. HELP 8 Show the full command list. GET FW VER 8 Show the unit’s current firmware version. SET FACTORY DEFAULT 8 Reset all configurations to the factory defaults. - Page 9 NEUVIDEO RS-232 & Telnet Commands RS-232 Commands COMMAND DESCRIPTION & PARAMETERS SET OUT A TIMING N1 8 Set the scaled output resolution. [720P50] [1366x768] Available values for N1: [1080P24] [1440x900] [Native] [1080P25] [1600x900RB] [480P60] [1080P30] [1600x1200] [720P60] [1024x768] [1680x1050] [1080P60] [1280x800] [1920x1200RB] [576P50]...
- Page 10 NEUVIDEO RS-232 & Telnet Commands RS-232 Commands COMMAND DESCRIPTION & PARAMETERS Force input N1 to use a specific color format. SET IN N1 FORMAT N2 8 N1 = 1 ~ 2 [Input port] Available values for N2: [RGB] [YPbPr 4:2:2] [YPbPr 4:4:4] Show the currently set color space format used by input N1.
- Page 11 NEUVIDEO RS-232 & Telnet Commands RS-232 Commands COMMAND DESCRIPTION & PARAMETERS GET CHROMAKEY N1 RANGE 8 Show the current key range set for the selected color component. Available values for N1: [Red component] GREEN [Green component] BLUE [Blue component] Set the horizontal position of the upper-left corner of input N1’s window in pixels. The SET IN N1 HPOSITION N2 8 maximum position value is the current horizontal resolution minus 1.
- Page 12 NEUVIDEO RS-232 & Telnet Commands RS-232 Commands COMMAND DESCRIPTION & PARAMETERS Show the current horizontal flip state for input N1. GET IN N1 FLIP 8 N1 = 1 ~ 2 [Input port] Enable or disable the video freeze function for input N1. SET IN N1 IMAGE STILL N2 8 N1 = 1 ~ 2 [Input port]...
- Page 13 NEUVIDEO RS-232 & Telnet Commands RS-232 Commands COMMAND DESCRIPTION & PARAMETERS GET OUT A OSD BACKDROP COLOR 8 Show the current OSD background color. SET OUT A OSD LOGO DISPLAY N1 8 Enable or disable the OSD graphical logo. Available values for N1: [Enabled] [Disabled] GET OUT A OSD LOGO DISPLAY 8...
-
Page 14: Webgui Control
NEUVIDEO WebGUI Control WebGUI Control • DEVICE DISCOVERY APP: Please obtain the “Device Discovery” software from your authorized dealer and save it in a directory where you can easily find it. Connect the unit and your PC/Laptop to the same active network and execute the “Device Discovery” software. - Page 15 NEUVIDEO WebGUI Control • INFORMATION BAR: Across the top of the WebGUI are 5 sections that will always be displayed no matter which tab has been selected. These sections are: Information-In, Information-Out, Source, Mode, and Preset/Factory. They provide information about the state of the unit, or control the most basic functions of the unit.
- Page 16 NEUVIDEO WebGUI Control • HUE: Sets the hue value for each input channel with a range of 0 to 100. Clicking on the slider will allow fine adjustments using the arrow keys. The default value is 50. • OUTPUT RESOLUTION: Sets the unit’s output resolution. The default selection is 1080p60. •...
- Page 17 NEUVIDEO WebGUI Control ■ Edit: Clicking this button opens the OSD Information Edit window to change the formatting of the OSD. Text: Define a text string to display on the OSD. Font Color: Set the color of the OSD font. Background Color: Set the background color of the OSD’s text block.
- Page 18 NEUVIDEO WebGUI Control • NETWORK TAB: This tab provides access to control of the IP configuration and Login settings for the unit. • IP CONFIGURATION: The IP Address, Netmask and Gateway can be set manually, or DHCP can be enabled for automatic IP Configuration if your local network supports it.
-
Page 19: Connection Diagram
NEUVIDEO CONNECTION DIAGRAM CONNECTION DIAGRAM... - Page 20 BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at the return address set forth on the Product’s packing label at your expense.