Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ryobi RTS721S
Summary of Contents for Ryobi RTS721S
- Page 1 RTS721S 178MM TILE SAW WITH FOLDING STAND OPERATOR’S MANUAL...
- Page 2 DESCRIPTION 1. Power cord 2. Drip loop 3. Residual current device (RCD) 4. Tile cutting blade 5. On/Off switch 6. Rip guide 7. Mitre guide 8. Max fill line 9. Overflow drain 10. Water reservoir 11. Rip fence scale 12. Stand 13.
- Page 3 Fig. 1 Fig. 2...
- Page 4 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7...
-
Page 5: Cross Cut
Fig. 8 Fig. 9 Fig. 10 Fig. 11 CROSS CUT DIAGONAL CUT Fig. 12 Fig. 13... -
Page 6: Mitre Cut
MITRE CUT L-CUT Fig. 14 Fig. 15 BEVEL CUT Fig. 17 Fig. 16 Fig. 18... - Page 7 Important! It is essential that you read the instructions in this manual before operating this machine. Subject to technical modifications.
-
Page 8: General Power Tool Safety Warnings
■ Do not overreach. Keep proper footing and balance GENERAL POWER TOOL SAFETY WARNINGS at all times. ■ Maintain tools with care. Keep tools sharp and clean WARNING for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool When using electric tools, basic safety precautions cords periodically and if damaged have them repaired should always be followed to reduce the risk of fire,... -
Page 9: Special Safety Rules
■ Inspect extension cords periodically and replace SPECIAL SAFETY RULES if damaged. ■ Always secure work firmly against the rip guide or ■ Ground all tools. If tool is equipped with three-prong bevel block. plug, it should be plugged into a three-hole electrical ■... -
Page 10: Grounding Instructions
motor. Wire that is heavy enough for a short distance will WARNING be too light for a greater distance. A line that can support one power tool may not be able to support two or three To reduce the risk of electrocution, keep all connections tools. - Page 11 Mitre guide ASSEMBLING THE STAND – The mitre guide is fully adjustable for diagonal cuts See Figure 7-8. and mitre cuts. The support brackets and stand legs have corresponding Motor letters for easy assembly. – This machine has a strong motor with sufficient Tools needed: Adjustable wrench or 13 mm wrenches and power to handle tough cutting jobs.
-
Page 12: Operation
OPERATION WARNING ALWAYS make sure your workpiece is not in contact WARNING with the cutting blade before operating the switch to start the tool. Failure to heed this warning may cause Do not allow familiarity with the products to make the workpiece to be kicked back toward the operator you careless. - Page 13 rip guide. 8. Hold the material firmly against the mitre guide and 4. Make sure the material is clear of the cutting blade slide mitre guide along rip fence. Feed the material before turning on the saw. into the cutting blade. 5.
-
Page 14: General Maintenance
5. Remove arbor nut, outer blade flange, and cutting For greater safety and reliability, all repairs should be blade. performed by an Authorised Ryobi Service Centre. 6. Wipe a drop of oil onto inner blade flange where it contacts the blade. -
Page 15: Environmental Protection
ENVIRONMENTAL PROTECTION Blade diameter Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for Blade arbor diameter environmental-friendly recycling. SYMBOL Net weight Safety alert Depth of cut (max.) Regulatory Compliance Mark (RCM). Product meets applicable... - Page 16 Techtronic Industries (Australia) Pty. Ltd. Level 1, 660 Doncaster Road Doncaster, VIC 3108, Australia Techtronic Industries New Zealand Ltd. 18-26 Amelia Earhart Avenue Mangere, Auckland 2022, New Zealand...
Need help?
Do you have a question about the RTS721S and is the answer not in the manual?
Questions and answers