Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FONESTAR PDA-207
Summary of Contents for FONESTAR PDA-207
- Page 1 PD -207 LOUDSPEAKER PROCESSOR 2 INPUTS AND 6 OUTPUTS INSTRUCTION MANUAL...
- Page 2 We take this opportunity to thank you for buying this product. We recommend you read the instruction manual before switching on the machine and follow the instructions that are given. Keep the manual for future reference. SECURITY AND THE ENVIRONMENT ELECTRICAL SECURITY Check that the current in the mains connection where the machine is to be installed corresponds to the power supply of the machine.
-
Page 3: Exemption Of Liability
The characteristics of the equipment and the content of the manual can change without forewarning. FONESTAR, S.A. does not assume responsibilities regarding the inappropriate use of the equipment or the information supplied in this instruction manual, and specifically disclaims any implied liability for marketability or fitness for any other use. -
Page 4: Controls And Functions Front Panel
DESCRIPTION Loudspeaker processor with 2 inputs and 6 outputs designed to process and adapt the audio signal to the characteristics of the P.A. system speakers offering an independent signal in each output. It incorporates equalization, frequency divider, gain control, limiter, delay and mute functions. CONTROLS AND FUNCTIONS FRONT PANEL 1.- CLIP and input level meters: LED indicators for the signal level in inputs A and B. -
Page 5: Back Panel
BACK PANEL 1.- AC INPUT: for connecting AC power supply cable. 2.- AES/EBU DIGITAL INPUT: digital AES/EBU type input, XLR connector. 3.- ETHERNET: port for connecting to a computer, RJ-45 connector. 4.- OUTPUTS 1-6: channel output connectors, XLR connector. 5.- INPUTS A-B: channel A and B input connectors, XLR connector. INSTRUCTIONS FOR USE GENERAL INFORMATION When you switch the equipment on, the current configuration is shown on the display:... -
Page 6: Input Configuration
INPUT CONFIGURATION The different input process functions can be set: GAIN, EQ, DELAY. To access the configuration menus press the IN button and choose the different process functions with the (a, d) selection buttons. GAIN For adjusting the signal level in each input individually. Note: as the gain is adjusted digitally, the user can select the desired input level, but has to be careful and not select too high a volume and saturate the signal. - Page 7 - Filter types (PEAK, LOW SH, HIGH SH). For selecting the filter type to be applied: Peaking Low shelving High shelving - Bypass. For deactivating the chosen filter. - Central frequency/ cutoff frequency (Hz). For choosing the central frequency of the peaking filter or the cut off frequency of the high pass or low pass filters.
-
Page 8: Output Configuration
- DELAY. For applying a delay to the input. To set the delay, follow the instructions below: - Press the IN button and using the (a, d) selection buttons, choose the DELAY option on the menu ( INA Delay or INB Delay will appear on the display). - Press the IN button again to change between input A and input B. - Page 9 HPF & LPF A high pass filter and low pass filter is allowed in each output. Each output has two displays, one for each filter, where the output number and filter type appear. To set the low and high pass filters, follow the instructions below: - Press the OUT button and using the (a, d) selection buttons, choose the LPF or HPF option from the menu (OPx HPF or OPx LPFwill appear on the display).
-
Page 10: Load Preset
- Press the OUT button and using the (a, d) selection buttons, choose the POLARITY option on the menu (OPx Polarity will appear on the display). - Press the OUT button again to change between different outputs. - Press ENTER. - Turn the ENTER control wheel to select normal or reverse polarity (insert a 180º... -
Page 11: Save Preset
To load another setting, follow the instructions below: - Press the LOAD button. - Select the configuration that you want to load using the (a, d) buttons. 10 base configurations are included (starting with the letter F, F00 to F09) and there are 70 memory banks available that can be editted by the user (starting with the letter U, U00 to U69). - Page 12 - Output meters: For choosing whether the point that the output level indicator signal is taken from is before or after the MUTE button. To set the point that the output level indicator signal is taken from, follow the instructions below: - Press the UTIL button and use the (a, d) selection buttons to choose the MISC SETUP option from the menu.
-
Page 13: Lock Submenu
- UART ID number: Shows the number of the system connected to the installation. - Noise gate: For activating or deativating the noise gate. If the noise gate is activated, there will be no input signal while the input signal level does not exceed the noise threshold. If the input signal level is higher than the noise gate, it will let the input signal pass. - Page 14 To unlock the system and modify configuration parameters, you will be asked for a password. Insert the password to unlock. Use the control keys to move the cursor and turn the ENTER control wheel to select the character to be inserted. Press ENTER to confirm. Important: if you forget the password, it is possible to delete the system memory.
- Page 15 CONNECTION The PDA-207 digital processor accepts multiple settings. There are two connection examples below: 4-WAY MONO SYSTEM + 2 MONITORS Input A to outputs 1, 2, 3 and 4 with independent equalization (A1234). The mix of inputs A and B to outputs 5 and 6 (S56).
- Page 16 3 -WAY STEREO SYSTEM (2 X 3 WAYS) Input A to outputs 1, 3 and 5 with independent equalization (A135). Input B to outputs 2, 4 and 6 with independent equalization (B246). - 16 -...
-
Page 17: Direct Connection To Pc
SOFTWARE The PDA-206 digital processor comes with software in a CD that lets you set the device when it is connected to a computer. It is composed of an intuitive system of windows that let you set the different functions and parameters that the processor has. - Page 18 - Go to the DHCP option using the (a, d) selection buttons. Press the ENTER button again and Disable this option. Then, switch the PDA-207 processor off using the button on the front panel of the equipment, connect the processor directly to the PC using the Cat 5e/6 cable supplied and switch the processor on again.
- Page 19 - Go to the DHCP option using the (a, d) selection buttons. Press the ENTER button again and Enable this option. Then, switch the PDA-207 processor off using the button on the front panel of the system, connect the processor to a switch using the Cat 5e/6 cable supplied and switch the processor on again.
-
Page 20: Block Diagram
BLOCK DIAGRAM - 20 -... -
Page 21: Specifications
SPECIFICATIONS PDA-207 CHARACTERISTICS Digital signal processor. Loudpeaker processor 2 inputs and 6 outputs. Parametric equalizers. Frequency divider (crossover). Compressor/limiter. 70 editable configurations. On mode selection. Front panel lock. 24 bit sigma delta convertors. 48 kHz frequency sampling. Ethernet port for PC connection. -
Page 22: Declaration Of Conformity
This product has been tested and has passed the corresponding quality control prior to being put on the market. FONESTAR guarantees the suitability of the product for its specified use during a period of 2 years from the delivery date and commits itself to repair or substitute the goods as expressed in the Spanish law ‘La Ley General para la Defensa de los...
Need help?
Do you have a question about the PDA-207 and is the answer not in the manual?
Questions and answers