Advertisement
Quick Links
DS437T Quick Guide【 English 】
Front Panel
F1
F1. SD Card Reader
F2. Power Button
F3. HDD LED
F4. Power LED
F2
F5. USB2.0 Ports x2
F4
F6. USB3.0 Ports x2
Back Panel
B1
B1. CMOS and External Power On Header
B2. DVI-I Port
B3
B3. HDMI Port
B4
B4. Mic-In
B5. Headphone
B6
B6. USB3.0 Ports x2
B7. LAN Port
B8
B8. USB2.0 Ports x2
B9. DC IN
Motherboard Illustration
HDD LED
Power LED
USB 3.0 Ports x2
USB 2.0 Ports x2
2.5 inch HDD slot
Half size Mini-PCIE slot - CN3
USB 3.0 Ports x2
USB 2.0 Ports x2
DC IN
LAN Port
Headphone
Jumper Settings
Power Button
C1
Pin Assignments (SW3)
SMBUS
C2
Pin Assignments (CN6):
F3
1=SMBCLK_SB
1
2=SMBDATA_SB
F5
3=+5V
4=GND
F6
Safety Information
Read the following precautions before setting up a Shuttle XPC.
CAUTION
Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent
as recommended by Shuttle. Dispose of used batteries according to the manufacturer's instructions.
B2
Left / Right Panel
B5
Kensington® Lock Port
B7
B9
Power Button - SW3
C1
SMBUS
C2
Power On Header - SW1
C3
Intel® NM70 Chipset
LPC Header
C4
Intel® Celeron®
Battery Connector - CN1
C5
Processor 1037U
DDR3 SODIMM slots
Audio Connector - AUDIO2
C6
External Power On Header - SW2
C7
DVI-I Port
HDMI Port
Mic In
LPC
Power On Header
C3
C4
Pin Assignments (SW1):
Pin Assignments (TPM1):
1=+HD_LED
1=TPM_33M
2=PWR_LED
2=GND
3=FRAME
3=-HD_LED
1
5=SIORST
4=GND
6=NC
3
5=RST_SW
5
7=LAD3
6=PWR_SW
8=LAD2
7
7=GND
9=+3.3V
9
8=GND
10=LAD1
11
9=NUUL
11=LAD0
13
12=GND
15
13=NC
17
1
2
14=NC_ID
19
3
4
15=+3.3VS
5
6
16=SERIRQ
8
7
17=GND
9
18=CLKRUN_NC
19=PD#_NC
20=NC_SUSCLK_R
A. Begin Installation
1. Unscrew the two screws of the chassis cover.
2. Slide the cover forwards and upwards.
Kensington® Lock Port
B. Memory Module Installation
1. Locate the SODIMM slot on the mainboard.
2. Align the notch of the memory module with the one of the memory slot.
Super I/O
3. Gently insert the module into the slot in a 45-degree angle.
4. Carefully push down the memory module until it snaps into the locking
5. Repeat the above steps to install additional memory modules, if required.
L
The product's color and specification will depend on the actual shipping product.
Battery Connector
C5
C6
Pin Assignments (CN1):
1=V_BAT
2=GND
1
2
4
6
8
10
12
14
External Power On Header
C7
16
Pin Assignments (SW2):
18
4
3
20
1=PWRSW-
2=+5V
3=GND
4=Clear Cmos
2
1
C. Component Installation
1. Unscrew the rack from the chassis.
For safety reasons, please ensure that the power cord is discon-
nected before opening the case.
2. Place the HDD in the rack and secure with the two screws from the side.
2
1
3. Put the HDD in the chassis and push toward right untill it inserts into the
SATA&SATA Power Connector.
SODIMM slot
notch
4. Refasten the screw.
mechanism.
D. Complete
1. Replace the covers and refasten the screws.
1
2
45-degree
angle
2 . Complete.
3
Please load the optimized BIOS settings.
Operation Position:
1) Device must only be used in vertical position with the DVI
port facing up.
Latch
Latch
2) Please make sure to use either the supplied feet or the VESA
mount.
Audio Connector
Pin Assignments (Audio2):
1=PULL AGND
2=LINE-R
3=N/C
4=LINE-L
5=PULL AGND
6=FRONT_L
7=N/C
8=FRONT_SENSE
9=PULL AGND
10=FRONT_R
11=BK_AUDIO-JD
12=MIC1_R
13=AGND
14=MIC1_L
13 11 9
7
5
3 1
14 12 10 8
6
4
2
53R-DS4373-2401
Advertisement
