Advertisement
Quick Links
DS67U Quick Guide【 English 】
__p
Front Panel
F1
F2
F3
F4
F6
F7
F5
F8
Back Panel
B9
B1
B2
B3 B4
B5
B6
B7
B8
Left / Right Panel
Kensington
®
Lock
Motherboard Illustration Front
Power Button - SW3
HDD LED
Power LED
USB 3.0 Ports x2
USB 2.0 Ports x2
2.5 inch HDD Slot
M.2 2242 M Key Slots
M.2 2230 E Key Slots
DC IN
LAN Ports x2
USB 2.0 Ports x2
Headphone JACK
62R-DS67U0-5201
DS67U
English.Spanish.Korean.
Traditional Chinese.Japanese.
French. German Quick Guide
Motherboard Illustration Back
F1. USB 3.0 Ports x2
F2. USB 2.0 Ports x2
F3. Power LED
F4. HDD LED
F5. Power Button
F6. COM 1 :
Support RS232/RS422/RS485
F7. COM 2 :
Support RS232
F8. SD Card Reader
®
®
Intel
Celeron
/ Core
processor
B1. External Power & Clear CMOS
(Pin definition
)
J4
B2. DisplayPort
B3. HDMI Port
B4. MIC-in Jack
B5. Headphone Jack
B6. USB 2.0 Ports x2
B7. LAN Ports x2
B8. DC IN
B9. Connectors for WLAN antennas
COM Port 1
J1
RS-232, RS-422, RS-485 switch by BIOS setting
1 2 3 4 5
Kensington
®
Lock
COM1 (RS232)
Pin
Signal Name
1
DCD
3
TX
5
GND
7
RTS
9
RI-
COM1 & COM2 Power Switch
RTC Battery Connector - BAT1
J2
COM Port 1
J1
COM Port 2
COM1 (pin9)
Short Pin
Function
COM1 & COM2
J2
1-2 (Default)
RI1
Power Switch - JP1
5-7
+5V
Debug Header
7-9
+12V
AC Back Auto Power ON
J3
DDR3L SO-DIMM Slots
Pin
AC Back auto Power ON function
AC Back Auto Power ON
J3
(DEFAULT =>Disable,
Short 1-2
Disable (Default)
short 1-2) - JP9
Open
Enable
External Power SW & Clear CMOS
J4
SW2
Pin
Signal Name
1
PWRSW-
2
+5V
3
GND
4
RTC_RST#
Safety Information
External Power SW &
J4
Clear CMOS - SW2
Read the following precautions before setting up a Shuttle XPC.
DisplayPort
CAUTION
HDMI Port
Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle.
MIC-in JACK
Dispose of used batteries according to the manufacturer's instructions.
SD Card Reader FFC
Connector - CON3
™
i series
Jumper Settings
COM1 (RS422)
Pin
Signal Name
Pin
Signal Name
1
TXD-
2
TXD+
3
RXD-
4
RXD+
5
GND
6
---
7
---
8
---
9
---
6 7 8 9
COM1 (RS485)
Pin
Signal Name
Pin Signal Name
Pin Signal Name
1
Data-
2
Data+
2
RX
4
DTR
3
---
4
---
6
DSR
5
GND
6
---
8
CTS
7
---
8
---
9
---
2
4
6
8
10
JP1
COM2 (pin9)
Short Pin
Function
3-4 (Default)
RI2
6-8
+5V
1
3
5
7
9
8-10
+12V
JP9
2
1
2
4
1
3
A. Begin Installation
2. Place the HDD or SSD in the rack and secure with the two screws from
the side.
For safety reasons, please ensure that the power cord is discon-
nected before opening the case.
1. Unscrew two screws of the chassis cover.
3. Lay the HDD or SSD into its drive bay and push it gently to the right
until it clicks into place.
2. Slide the cover forwards and upwards.
2
1
4. Refasten screws.
B. Memory Module Installation
This mainboard does only support 1.35V DDR3L memory
modules.
1. Locate the SO-DIMM slot on the mainboard.
5. As shown, unfasten the screw first.
2. Align the notch of the memory module with the one of the memory slot.
6. Install the M.2 device into the M.2 slot and secure with the screw.
Supports DDR3L SO-DIMM
notch
(1.35V)
3. Gently insert the module into the slot in a 45-degree angle.
4. Carefully push down the memory module until it snaps into the locking
mechanism.
D. Complete
1. Replace the covers and refasten the screws.
1
2
45-degree
angle
3
2.
Screw the included antennas onto the appropriate connectors at the back panel (B9).
Make sure they are aligned vertically or horizontally to achieve the best possible
signal reception.
Make sure all antennas are aligned in the correct direction.
Latch
Latch
5. Repeat above steps to install additional memory modules, if required.
C. Component Installation
1. Unscrew the rack from chassis.
3. Complete.
Please press the "Del" key while booting to enter BIOS.
Here, please load the optimised BIOS settings.
Operation Position:
Please make sure to use either the supplied feet or the VESA mount.
L
The product's colour and specifications may vary from the actually shipping product.
53R-DS67U3-H001
Advertisement
