Audio Signal Connections - MartinLogan Dynamo 600X User Manual

Setting Control
Figure 2.
(Switch)
Controls and inputs.
App / Local
D 600X
ynamo
D 800X
ynamo
D 1100X
ynamo
D 1600X
ynamo
Figure 3.
Audio signal inputs.
Left In &
Right In
D 600X
ynamo
D 800X
ynamo
D 1100X
ynamo
D 1600X
ynamo
The ARC Mobile app can use a Bluetooth connection to the
subwoofer. Use of your subwoofer's built-in USB Input is not
required to run Anthem Room Correction.
For those who desire to run ARC using a computer, the USB Input
allows connection of your subwoofer to a computer via a Micro
USB connection. Depending on the version of your ARC kit (sold
separately) you may need a USB (Type A) to Micro-B USB cable
or a Mini-B USB (Female) to Micro-B USB (Male) adapter.
The USB Input can also be used to apply firmware updates to your
subwoofer.
Status
Your subwoofer is equipped with a multi-color LED to indicate the
current status of the subwoofer.
• No color: No power. The subwoofer is not plugged in or has
shutdown due to an overload condition. Unplug the subwoofer
and plug it back in to correct.
• White: Play mode. This indicates the subwoofer detects an
audio signal and has automatically switched into play mode.
• Red: Standby. The sub has switched into power saving mode.
• Flashing: Error. The sub is displaying an error code.
Level
(Knob)
Min – Max
ü ü
ü ü
ü ü
ü ü
Line Level
(RCA)
LFE In
ü (Right In doubles as LFE In))
ü ü
ü ü
ü ü
USB Input Status
(Micro-B USB) (LED)
– –
ü ü
ü ü
ü ü
ü ü
Balanced
(XLR)
LFE In
–
–
ü
ü
Power Mode and Trigger Input
The Power Mode switch allows control of when the subwoofer
turns on and off.
• Auto: When set to 'Auto' the subwoofer will turn itself on when
detecting an audio signal. After several minutes of inactivity the
subwoofer will put itself in standby mode.
• On: When set to 'On' the subwoofer will always be on.
• Trigger: D
800X, 1100X, and 1600X are equipped
ynamo
with a trigger input. If you have an external source component
(such as a receiver) with built in trigger controls, you may wish
to turn the subwoofer on and off using this source. Connect a
cable from the control component to your subwoofer's Trigger
Input and set the Power Mode switch to 'Trigger'. Although
this technology is commonly referred to as a 12V trigger, the
subwoofer will respond to any signal between 5–24V DC.

Audio Signal Connections

Line Level Input (Left In / Right In)
Found on D 600X, 800X, 1100X, and 1600X. Please
ynamo
note, on the 600X the Right In also serves as the LFE In. Connect
from the Main Out or Pre Out on your receiver/pre-amp. The set-
ting for the Low-Pass Filter control is applied to the signal received
through these inputs.
12V Trigger
Power Mode
Input
On / Auto
ü
ü (+ Trigger)
ü (+ Trigger)
ü (+ Trigger)
Speaker Level Wireless Audio
(Banana Jacks) (sold separately)
Left In & Left In &
Right In Right In (LFE In)
ü ü
ü ü
ü ü
ü ü
–
ü
ü
ü
3