Inovonics EE1261 Installation Instructions

EE1261 EchoStream® Four-Element
Motion Detector
Installation Instructions
1 Overview
The EE1261 is a wireless motion detector that features a detection range of
15 meters, fixed or variable sleep time, a walk test feature, a front and rear
tamper switch, and increased immunity to radio frequency interference,
vibration, static, lighting ambient temperature changes, and other causes of
false activation. The EE1261 is designed with pet immunity up to 15kg
weight and 30cm height.
Caution: The EE1261 needs one minute for stabilization after power up.
During the stabilization period, the LED will blink twice per second, and the
EE1261 will not be operational.
Caution: Prior to operation, the EE1261 must be acclimated to the
temperature of the install environment for a period of 60 minutes.
1.1 Inovonics Wireless Contact Information
If you have any problems with this procedure, contact Inovonics Wireless
technical services:
• E-mail: support@inovonics.com.
• Phone: (800) 782-2709; (303) 939-9336.
1.2 EE1261 Components
A
F
C
Figure 1 EE1261 components
A EchoStream Select pins B Reset button
D Test mode reed switch E Sleep time selection
pins
G Sensitivity adjustment H Case tamper switch I Printed circuit board
dial
1.3 What's In The Carton
• Three wall mount screws.
• Three wall mount anchors.
• One selection jumper.
• One 3.0V lithium battery.
6/15/17 05308F © Inovonics, 2017 - www.inovonics.com P/N 7103855 Rev. C
B
I
E
D
H
G
C Pulse count selection
pins
F Sleep duration
selection pins
(pcb) mounting screw
2 Installation and Startup
2.1 Installation Notes
• These products are designed to be installed and maintained by
professional security technicians.
• Products are intended for indoor use.
• Manually test all products weekly.
2.2 Install/Replace Battery
To install the battery:
1. Release the housing screw and raise the cover.
Figure 2 Open the cover
2. Install the battery.
3. Press the reset button.
2.3 Enable EchoStream Select
To meet ETSI requirements, Inovonics has developed a new line of EE
868MHz-only products. These new 868MHz-only products are compatible
with older systems that include EchoStream Select (ES) products. If you
are not using any ES products in your current system, skip to section 2.4,
"Select Automatic/Pulse Count"; if you are using any ES products in your
current system, you will need to enable EchoStream Select compatibility on
this new 868MHz-only product.
To enable EchoStream Select compatibility:
4. Place a selection jumper on the ES selection pins.
Note: The selection jumper is included in the EE1261 hardware packet.
Note: EN50131-2-2; Security Grade 2 requires this selection jumper not be
installed.
5. Press the reset button.
2.4 Select Automatic/Pulse Count
The pulse count jumper setting provides control for normal or difficult
operating environments. Automatic pulse count is recommended for
reliable operation in environments subject to temperature fluctuations that
may cause false alarms. The single pulse count mode is more sensitive to
minor temperature variations, and should be used in sites where variant
heat sources will not cause false alarms.
The EE1261 is configured for single pulse count by default. If you are
planning to use the EE1261 in single pulse count, skip to section 2.5,
"Select Fixed/Variable Sleep Time"; if you are planning to use the EE1261
in automatic pulse count, you will need to configure it.
To configure the EE1261 for automatic pulse count:
6. Move the selection jumper on the pulse count selection pins to the left
two pins, marked AUTO, to select automatic pulse count.
7. Press the reset button.
2.5 Select Fixed/Variable Sleep Time
When set to variable, if the EE1261 senses motion, it will transmit an alarm,
then enter sleep mode for the sleep time duration; if motion is sensed
before the sleep time duration has expired, the EE1261 will restart the
sleep time duration. Variable sleep time is the recommended, default
setting for high-traffic commercial environments.
When set to fixed, if the EE1261 senses motion, it will transmit an alarm,
then enter sleep mode until the sleep time duration expires; if motion is
sensed when the sleep time duration has expired, the EE1261 will transmit
another alarm. Fixed sleep time is only recommended for low traffic,
residential operating environments.
Housing
screw
1